Upgrade Oracle RAC cluster 11.2.0.3 on OEL 6.1 to Oracle RAC

Upgrade Oracle RAC cluster 11.2.0.3 on OEL 6.1 to
Oracle RAC cluster 12c on OEL6.5
In the article you will have a look at the guidelines and steps to upgrade an
Oracle RAC cluster 11.2.0.3 on OEL 6.1 to Oracle RAC cluster 12c on OEL 6.5.
The initial cluster configuration (Oracle 11.2.0.3 on OEL 6.1) is described
here. The upgrade comprises the following steps:
1. Rolling upgrade of the Virtual Box machines (OEL61A and OEL61B) from
OEL 6.1 to OEL 6.5 with UEKR3 (kernel 3.8.13-35.el6uek.x86_64)
2. Upgrade from Oracle 11gR2 11.2.0.3 to Oracle 12c 12.1.0.1 for both
GI/RDBMS software. The database upgrade involves a downtime during the
upgrade.
The following software will be used:
1. Oracle VM Virtual Box 4.3.12 – download from here.
2. Oracle 12c (database, grid, examples) – download from OTN here.
3. Oracle OEL 6.5 – download from Oracle Software Delivery Cloud (former
Edelivery) here.
I upgraded the Oracle VM Virtual Box software, used in the setup here, to the
latest version available at the time of writing the article. Thus,
henceforth, I will not discuss the Oracle VM Virtual Box software upgrade in
the article.
I will use the existing VMs (OEL61A and OEL61B) without any change from the
original configuration for the upgrade to OEL65 and Oracle 12c. The only
changes are to enable internet access for the duration of the OEL upgrade
Overall, I must admit, I was quite impressed by how easy and smooth the
upgrade was compared to similar Oracle RAC upgrades from 9i->10g->11g where I
had to spend longer time on MOS (former Metalink) working around upgrade
issues.
1. Rolling upgrade of the Virtual Box machines (OEL61A and
OEL61B) from OEL 6.1 to OEL 6.5 with UEKR3 (kernel 3.8.1335.el6uek.x86_64)
Prior to the upgrade, OEL61A and OEL61B are running Oracle Enterprise Linux
(OEL) 6.1. I will upgrade it to OEL 6.5 using UEKR3 3.8.13-35.el6uek.x86_64.
I will implement an upgrade procedure first on OEL61A while Oracle is running
on OEL61B and then I will implement the same procedure on OEL61B while OEL61A
is running upgraded to OEL65.
Essentially, you must make sure that you can run successfully ‘yum upgrade’
and ‘yum install’ commands while connected to the appropriate channel. The
procedure is as follows:
1.1
1.2
Stop Oracle Clusterware and the database on the node where the
upgrade to OEL 6.5 is to be performed.
Configure any interface on oel61a/oel61b to obtain IP through DHCP
only for the duration of the upgrade from OEL 6.1 to OEL 6.5.
Required to obtain an internet connection to the Public YUM
repository.
The change can be made on this screen. For example on OEL61A from
the fixed IP change to DHCP obtained IP.
Later I will disable the NetworkManager as it rewrites
/etc/resolv.conf
1.3
Change Oracle VM Virtual Box network adapter for the corresponding
OEL interface to NAT from bridge only for the duration of the
upgrade. Required to obtain an internet connection to the Public YUM
repository. The change will have to be made on this screen.
1.4
1.5
1.6
1.7
1.8
Restart the VM
Stop Oracle Clusterware and the database where the upgrade is
performed.
Go to /etc/yum.repos.d/ directory running cd /etc/yum.repos.d/
Pull the repository running the following command wget
http://public-yum.oracle.com/public-yum-ol6.repo
Edit the public-yum-ol6.repo to enable access to ol6_latest,
public_ol6_UEKR3_latest, public_ol6_UEK_latest, public_ol6_ofed_UEK.
[[email protected] yum.repos.d]# cat public-yum-ol6.repo
[public_ol6_latest]
name=Oracle Linux $releasever Latest ($ba search)
baseurl=http://publicyum.oracle.com/repo/OracleLinux/OL6/latest/$basearch/
gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-oracle
gpgcheck=1
enabled=1
[public_ol6_addons]
name=Oracle Linux $releasever Add ons ($basearch)
baseurl=http://publicyum.oracle.com/repo/OracleLinux/OL6/addons/$basearch/
gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-oracle
gpgcheck=1
enabled=0
[public_ol6_ga_base]
name=Oracle Linux $releasever GA installation media copy ($basearch)
baseurl=http://publicyum.oracle.com/repo/OracleLinux/OL6/0/base/$basearch/
gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-oracle
gpgcheck=1
enabled=0
[public_ol6_u1_base]
name=Oracle Linux $releasever Update 1 installation media copy
($basearch)
baseurl=http://publicyum.oracle.com/repo/OracleLinux/OL6/1/base/$basearch/
gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-oracle
gpgcheck=1
enabled=0
[public_ol6_u2_base]
name=Oracle Linux $releasever Update 2 installation media copy
($basearch)
baseurl=http://publicyum.oracle.com/repo/OracleLinux/OL6/2/base/$basearch/
gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-oracle
gpgcheck=1
enabled=0
[public_ol6_u3_base]
name=Oracle Linux $releasever Update 3 installation media copy
($basearch)
baseurl=http://publicyum.oracle.com/repo/OracleLinux/OL6/3/base/$basearch/
gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-oracle
gpgcheck=1
enabled=0
[public_ol6_u4_base]
name=Oracle Linux $releasever Update 4 installation media copy
($basearch)
baseurl=http://publicyum.oracle.com/repo/OracleLinux/OL6/4/base/$basearch/
gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-oracle
gpgcheck=1
enabled=0
[public_ol6_u5_base]
name=Oracle Linux $releasever Update 5 installation media copy
($basearch)
baseurl=http://publicyum.oracle.com/repo/OracleLinux/OL6/5/base/$basearch/
gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-oracle
gpgcheck=1
enabled=0
[public_ol6_UEKR3_latest]
name=Latest Unbreakable Enterprise Kernel for Oracle Linux $releasever
($basearch)
baseurl=http://publicyum.oracle.com/repo/OracleLinux/OL6/UEKR3/latest/$basearch/
gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-oracle
gpgcheck=1
enabled=1
[public_ol6_UEK_latest]
name=Latest Unbreakable Enterprise Kernel for Oracle Linux $releasever
($basearch)
baseurl=http://publicyum.oracle.com/repo/OracleLinux/OL6/UEK/latest/$basearch/
gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-oracle
gpgcheck=1
enabled=1
[public_ol6_UEK_base]
name=Unbreakable Enterprise Kernel for Oracle Linux $releasever
($basearch)
baseurl=http://publicyum.oracle.com/repo/OracleLinux/OL6/UEK/base/$basearch/
gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-oracle
gpgcheck=1
enabled=0
[public_ol6_playground_latest]
name=Latest mainline stable kernel for Oracle Linux 6 ($basearch) Unsupported
baseurl=http://publicyum.oracle.com/repo/OracleLinux/OL6/playground/latest/$basearch/
gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-oracle
gpgcheck=1
enabled=0
[public_ol6_MySQL]
name=MySQL 5.5 for Oracle Linux 6 ($basearch)
baseurl=http://publicyum.oracle.com/repo/OracleLinux/OL6/MySQL/$basearch/
gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-oracle
gpgcheck=1
enabled=0
[public_ol6_gdm_multiseat]
name=Oracle Linux 6 GDM Multiseat ($basearch)
baseurl=http://publicyum.oracle.com/repo/OracleLinux/OL6/gdm_multiseat/$basearch/
gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-oracle
gpgcheck=1
enabled=0
[public_ol6_ofed_UEK]
name=OFED supporting tool packages for Unbreakable Enterprise Kernel on
Oracle Linux 6 ($basearch)
baseurl=http://publicyum.oracle.com/repo/OracleLinux/OL6/ofed_UEK/$basearch/
gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-oracle
gpgcheck=1
enabled=1
[public_ol6_MySQL56]
name=MySQL 5.6 for Oracle Linux 6 ($basearch)
baseurl=http://publicyum.oracle.com/repo/OracleLinux/OL6/MySQL56/$basearch/
gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-oracle
gpgcheck=1
enabled=0
[public_ol6_spacewalk20_server]
name=Spacewalk Server 2.0 for Oracle Linux 6 ($basearch)
baseurl=http://publicyum.oracle.com/repo/OracleLinux/OL6/spacewalk20/server/$basearch/
gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-oracle
gpgcheck=1
enabled=0
[public_ol6_spacewalk20_client]
name=Spacewalk Client 2.0 for Oracle Linux 6 ($basearch)
baseurl=http://publicyum.oracle.com/repo/OracleLinux/OL6/spacewalk20/client/$basearch/
gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-oracle
gpgcheck=1
enabled=0
[[email protected] yum.repos.d]#
1.9
1.10
Run yum install oracle-rdbms-server-12cR1-preinstall
Run yum update. As the output is quite long I will not include it. I
encountered the following problem.
Total
168 kB/s | 294 kB
00:01
Running rpm_check_debug
ERROR with rpm_check_debug vs depsolve:
libqpidclient.so.5()(64bit) is needed by (installed) matahari -net-0.4.05.el6.x86_64
libqpidclient.so.5()(64bit) is needed by (installed) libvirt-qpid-0.2.226.el6.x86_64
libqpidcommon.so.5()(64bit) is needed by (installed) matahari -net-0.4.05.el6.x86_64
libqpidcommon.so.5()(64bit) is needed by (installed) libvirt-qpid-0.2.226.el6.x86_64
libmcommon.so.0.0.1()(64bit) is needed by (installed) matahari-net-0.4.05.el6.x86_64
libmnet.so.0.0.1()(64bit) is needed by (installed) matahari-net-0.4.05.el6.x86_64
matahari-lib = 0.4.0-5.el6 is needed by (installed) matahari-net-0.4.05.el6.x86_64
libmqmfagent.so.0.0.1()(64bit) is needed by (installed) matahari-net0.4.0-5.el6.x86_64
matahari-agent-lib = 0.4.0-5.el6 is needed by (installed) matahari-net0.4.0-5.el6.x86_64
libqmf.so.4()(64bit) is needed by (installed) libvirt-qpid-0.2.226.el6.x86_64
Please report this error in http://yum.baseurl.org/report
You could try running: rpm -Va --nofiles --nodigest
Your transaction was saved, rerun it with: yum load -transaction
/tmp/yum_save_tx-2014-05-20-20-10Xp21Gm.yumtx
[[email protected] yum.repos.d]# yum install
1.11
Use the fix for BUG 919514
In my case I ran the following. If you have problems with different
rpms adjust accordingly.
yum shell
install matahari
remove matahari-service
remove matahari-lib
remove matahari-host
remove matahari-agent
remove matahari-net
run
exit
yum shell
install libvirt-qpid
remove libvirt-qpid
run
exit
1.12
1.13
1.14
1.15
Rerun yum update
Install Guest Additions CD. Required for Clipboard and mouse
integration.
Change the eth0 configuration back to the fixed IP from IP obtained
from DHCP. Essentially, it reverses what I did in 1.2
Change /etc/grub.conf so that by default to boot 3.8.1335.el6uek.x86_64 and optimize it by adding divider=10.
[[email protected] db_1]# cat /etc/grub.conf
# grub.conf generated by anaconda
#
# Note that you do not have to rerun grub after making changes to this
file
# NOTICE: You have a /boot partition. This means that
#
all kernel and initrd paths are relative to /boot/, eg.
#
root (hd0,0)
#
kernel /vmlinuz-version ro root=/dev/sda5
#
initrd /initrd-[generic-]version.img
#boot=/dev/sda
default=2
timeout=5
splashimage=(hd0,0)/grub/splash.xpm.gz
hiddenmenu
title Oracle Linux Server Red Hat Compatible Kernel (2.6.32431.el6.x86_64)
root (hd0,0)
kernel /vmlinuz-2.6.32-431.el6.x86_64 ro root=UUID=ef6e890d-860a4554-bb70-4315af978e6b rd_NO_LUKS rd_NO_LVM rd_NO_MD rd_NO_DM
LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us
rhgb quiet numa=off transparent_hugepage=never crashkernel=auto
initrd /initramfs-2.6.32-431.el6.x86_64.img
title Oracle Linux Server (3.8.13-35.el6uek.x86_64.debug)
root (hd0,0)
kernel /vmlinuz-3.8.13-35.el6uek.x86_64.debug ro
root=UUID=ef6e890d-860a-4554-bb70-4315af978e6b rd_NO_LUKS rd_NO_LVM
rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16
KEYBOARDTYPE=pc KEYTABLE=us rhgb quiet numa=off
transparent_hugepage=never
initrd /initramfs-3.8.13-35.el6uek.x86_64.debug.img
title Oracle Linux Server (3.8.13-35.el6uek.x86_64)
root (hd0,0)
kernel /vmlinuz-3.8.13-35.el6uek.x86_64 ro root=UUID=ef6e890d 860a-4554-bb70-4315af978e6b rd_NO_LUKS rd_NO_LVM rd_NO_MD rd_NO_DM
LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us
rhgb quiet numa=off transparent_hugepage=never divider=10
initrd /initramfs-3.8.13-35.el6uek.x86_64.img
title Oracle Linux Server-uek (2.6.32-100.34.1.el6uek.x86_64)
root (hd0,0)
kernel /vmlinuz-2.6.32-100.34.1.el6uek.x86_64 ro
root=UUID=ef6e890d-860a-4554-bb70-4315af978e6b rd_NO_LUKS rd_NO_LVM
rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16
KEYBOARDTYPE=pc KEYTABLE=us rhgb quiet numa=off
transparent_hugepage=never
kernel /vmlinuz-2.6.32-100.34.1.el6uek.x86_64 ro
root=UUID=ef6e890d-860a-4554-bb70-4315af978e6b rd_NO_LUKS rd_NO_LVM
rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16
KEYBOARDTYPE=pc KEYTABLE=us rhgb quiet numa=off
transparent_hugepage=never
initrd /initramfs-2.6.32-100.34.1.el6uek.x86_64.img
title Oracle Linux Server-uek-debug (2.6.32-100.34.1.el6uek.x86_64.debug)
root (hd0,0)
kernel /vmlinuz-2.6.32-100.34.1.el6uek.x86_64.debug ro
root=UUID=ef6e890d-860a-4554-bb70-4315af978e6b rd_NO_LUKS rd_NO_LVM
rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16
KEYBOARDTYPE=pc KEYTABLE=us rhgb quiet numa=off
transparent_hugepage=never
initrd /initramfs-2.6.32-100.34.1.el6uek.x86_64.debug.img
title Oracle Linux Server (2.6.32-131.0.15.el6.x86_64)
root (hd0,0)
kernel /vmlinuz-2.6.32-131.0.15.el6.x86_64 ro root=UUID=ef6e890d860a-4554-bb70-4315af978e6b rd_NO_LUKS rd_NO_LVM rd_NO_MD rd_NO_DM
LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us
crashkernel=auto rhgb quiet numa=off transparent_hugepage=never
initrd /initramfs-2.6.32-131.0.15.el6.x86_64.img
[[email protected] db_1]#
1.16
1.17
1.18
1.19
1.20
1.21
1.22
Shutdown the VM
Change the VM network adapter back to bridged. Essentially, it
reverses what I did in 1.3
Start the VM
Stop GI and database on the node.
Re-link Oracle RDBMS and Oracle GI binaries. For GI binary relink
you might want to look at ‘How To Relink The Oracle Grid
Infrastructure Standalone (Restart) Installation Or Oracle Grid
Infrastructure RAC/Cluster Installation (11.2 or 12c). (Doc ID
1536057.1)’
Start GI and database on the node.
This concludes the upgrade from OEL 6.1 to OEL 6.5.
Before the upgrade I had
[[email protected] yum.repos.d]# uname -a
Linux oel61a.gj.com 2.6.32-100.34.1.el6uek.x86_64 #1 SMP Wed May 25
17:46:45 EDT 2011 x86_64 x86_64 x86_64 GNU/Linux
[[email protected] yum.repos.d]#
After the upgrade I have
[[email protected] ~]# uname -a
Linux oel61a.gj.com 3.8.13-35.el6uek.x86_64 #2 SMP Tue May 13 14:09:13
PDT 2014 x86_64 x86_64 x86_64 GNU/Linux
[[email protected] ~]#
Start the OEL61A VM and perform an upgrade using the above procedure to
OEL61B.
2.
Upgrade from Oracle 11gr2 11.2.0.3 to Oracle 12c 12.1.0.1
for both GI/RDBMS software. The database upgrade involves a
downtime during the upgrade .
Note that the some of the prerequisites to run 11.2.0.3 are also
prerequisites for running 12c. Installing oracle-rdbms-server-12cR1preinstall performed most of the prerequisites configurations. I addition
perform the following steps while both VMs are up and running
2.1
Run cluster verify utility. The output is in Annex A.
./runcluvfy.sh stage -pre crsinst -n oel61a,oel61b
./runcluvfy.sh stage -post hwos -n oel61a,oel61b
2.2
Make sure that the cluster is up and running
I ran
./crsctl check cluster –all
./crsctl stat res –t
The output is in Annex A
2.3
Create directories for the New GI 12c and the new RDBMS homes
mkdir
chown
mkdir
chown
-p
-R
–p
–R
/u01/app/12.1.0/grid
grid:oinstall /u01/app/12.1.0
/u01/app/oracle/product/12.1.0/db_1
oracle:oinstall /u01/app/oracle/product/12.1.0/db_1
2.4
Oracle 12c asks for avahi-daemon
Run the follow commends:
service avahi-daemon start
chkconfig avahi-daemon on
2.5
Addressing possible PRVE-0420 problem. Look at PRVE-0420 /dev/shm is
not found mounted on node (Doc ID 1568100.1). BUG:17080954 /DEV/SHM MOUNT OPTION WRONG.
PRVE-0420 : /dev/shm is not found mounted on node ""
PRVE-0420 : /dev/shm is not found mounted on node ""
If you observe the error while running the cluvfy or OUI prform the
following steps:
Change /etc/fstab to contain the line
tmpfs /dev/shm tmpfs
rw,exec,size=3500m 0 0
Run the following command
mount -o remount,size=3500m /dev/shm
The problem is fixed
[[email protected] ~]# mount -o
[[email protected] ~]# df -k
Filesystem
1K-blocks
/dev/sda5
9948012
/dev/sda1
9948012
/dev/sda6
9948012
/dev/sda7
9948012
/dev/sda8
9948012
/dev/sda11
218783604
/dev/sda9
9948012
/dev/sda10
9948012
/dev/sda2
9948012
D_DRIVE
976759804
E_DRIVE
1953382396
VM
1953382396
software
1953382396
tmpfs
3584000
[[email protected] ~]#
2.6
remount,size=3500m /dev/shm
Used Available Use% Mounted on
1092380
8327248 12% /
169128
9250500
2% /boot
23192
9396436
1% /home
47064
9372564
1% /opt
45900
9373728
1% /tmp
33712556 173934436 17% /u01
7948612
1471016 85% /usr
22640
9396988
1% /usr/local
4950092
4469536 53% /var
966175568 10584236 99% /media/sf_D_DRIVE
1898114636 55267760 98% /media/sf_E_DRIVE
1898114636 55267760 98% /media/sf_VM
1898114636 55267760 98% /media/sf_software
215908
3368092
7% /dev/shm
Set in Set in /etc/ssh/sshd_config
LoginGraceTime 0
2.7
Enabling the Name Service Cache Daemon
chkconfig --level 35 nscd on
service nscd start
2.8
Disable Linux Firewalls.
chkconfig iptables off
2.9
2.10
Install cvuqdisk-1.0.9-1.rpm
Change /etc/resolv.conf. Add the GNS
[[email protected] bin]# cat cat /etc/resolv.conf
cat: cat: No such file or directory
# Generated by NetworkManager
search gj.com
nameserver 192.168.2.1
nameserver 192.168.2.11
nameserver 192.168.2.52
[[email protected] bin]#
[[email protected] bin]# cat /etc/resolv.conf
# Generated by NetworkManager
search gj.com
nameserver 192.168.2.11
nameserver 192.168.2.1
nameserver 192.168.2.52
[[email protected] bin]#
2.11
Stop Network Manager in order to avoid over-writing /etc/resolv.conf
chkconfig NetworkManager off
service NetworkManager stop
2.12
2.13
2.14
Make profiles (.bash_profile) for grid and oracle users on both VMs
OEL61A and OEL61B . Look at the Annex A for details.
Unzip 12c binaries in a staging area and set permissions on the
staging area.
Run runInstaller from grid 12c stage area.
Select Skip and press Next to continue.
Select Upgrade and press Next.
Select the languages and press Next.
Make sure all nodes are selected and press Next.
Select the option to configure Grid Infrastructure Management
Repository.
Review the OS groups and press Next.
Review the location and press Next.
Opt to manually run the scripts.
Review the checks
The errors are as listed
The avahi-daemon is asked but then it complains. The rest can be
ignored. As this is Oracle VM Virtual Box environment memory
requirement is not important.
PRVF-7530 can be ignored. As this is Oracle VM Virtual Box
environment memory requirement is not important. In production
environment increase the RAM size to avoid the error.
PRVF-5636 can be ignored. As this is Oracle VM Virtual Box the error
can be ignored. Look at The DNS response time for an unreachable
node exceeded "15000" ms on following nodes (Doc ID 1356975.1) to
avoid the error in production environment.
PRVG-1359 cannot find info for the time being.
Daemon "avahi-daemon" not configured and running - This test checks that
the "avahi-daemon" daemon is not configured and running on the cluster
nodes.
Check Failed on Nodes: [oel61b, oel61a]
Verification result of failed node: oel61b Details:
-
PRVG-1359 : Daemon process "avahi-daemon" is configured on node "oel61b"
- Cause: The identified daemon process was found configured on the
indicated node. - Action: Ensure that the identified daemon process is
not configured on the indicated node.
PRVG-1360 : Daemon process "avahi-daemon" is running on node "oel61b" Cause: The identified daemon process was found running on the indicated
node. - Action: Ensure that the identified daemon process is stopped
and not running on the indicated node.
Back to Top
Verification result of failed node: oel61a Details:
PRVG-1359 : Daemon process "avahi-daemon" is configured on node "oel61a"
- Cause: The identified daemon process was found configured on the
indicated node. - Action: Ensure that the identified daemon process is
not configured on the indicated node.
PRVG-1360 : Daemon process "avahi-daemon" is running on node "oel61a" Cause: The identified daemon process was found running on the indicated
node. - Action: Ensure that the identified daemon process is stopped
and not running on the indicated node.
Back to Top
Physical Memory - This is a prerequisite condition to te st whether the
system has at least 4GB (4194304.0KB) of total physical memory.
Check Failed on Nodes: [oel61b, oel61a]
Verification result of failed node: oel61b
Expected Value
: 4GB (4194304.0KB)
Actual Value
: 3.8614GB (4048936.0KB)
Details:
PRVF-7530 : Sufficient physical memory is not available on node "oel61b"
[Required physical memory = 4GB (4194304.0KB)] - Cause: Amount of
physical memory (RAM) found does not meet minimum memory requirements. Action: Add physical memory (RAM) to the node specified.
Back to Top
Verification result of failed node: oel61a
Expected Value
: 4GB (4194304.0KB)
Actual Value
: 3.8614GB (4048936.0KB)
Details:
PRVF-7530 : Sufficient physical memory is not available on node "oel61a"
[Required physical memory = 4GB (4194304.0KB)] - Cause: Amount of
physical memory (RAM) found does not meet minimum memory requirements. Action: Add physical memory (RAM) to the node specified.
Back to Top
Task resolv.conf Integrity - This task checks consistency of file
/etc/resolv.conf file across nodes
Check Failed on Nodes: [oel61b, oel61a]
Verification result of failed node: oel61b Details:
PRVF-5636 : The DNS response time for an unreachable node exceeded
"15000" ms on following nodes: oel61a,oel61b - Cause: The DNS response
time for an unreachable node exceeded the value specified on nodes
specified. - Action: Make sure that 'options timeout', 'options
attempts' and 'nameserver' entries in file resolv.conf are proper. On
HPUX these entries will be 'retrans', 'retry' and 'nameserver'. On
Solaris these will be 'options retrans', 'options retry' and
'nameserver'. Make sure that the DNS server responds back to name lookup
request within the specified time when looking up an unknown host name.
Check for integrity of file "/etc/resolv.conf" failed - Cause: Cause Of
Problem Not Available - Action: User Action Not Available
Back to Top
Verification result of failed node: oel61a Details:
PRVF-5636 : The DNS response time for an unreachable node exceeded
"15000" ms on following nodes: oel61a,oel61b - Cause: The DNS response
time for an unreachable node exceeded the value specified on nodes
specified. - Action: Make sure that 'options timeout', 'options
attempts' and 'nameserver' entries in file resolv.conf are proper. On
HPUX these entries will be 'retrans', 'retry' and 'nameserver'. On
Solaris these will be 'options retrans', 'options retry' and
'nameserver'. Make sure that the DNS server responds back to name lookup
request within the specified time when looking up an unknown host name.
Check for integrity of file "/etc/resolv.conf" failed - Cause: Cause Of
Problem Not Available - Action: User Action Not Available
Back to Top
Confirm that you want to continue.
Wait until installation prompts for running scripts as root.
When prompted run as root
On oel61a
[[email protected] bin]# /u01/app/12.1.0/grid_1/rootupgrade.sh
Performing root user operation for Oracle 12c
The following environment variables are set as:
ORACLE_OWNER= grid
ORACLE_HOME= /u01/app/12.1.0/grid_1
Enter the full pathname of the local bin directory: [/usr/local/bin]:
The file "dbhome" already exists in /usr/local/bin. Overwrite it? (y/n)
[n]: y
Copying dbhome to /usr/local/bin ...
The file "oraenv" already exists in /usr/local/bin. Overwrite it? (y/n)
[n]: y
Copying oraenv to /usr/local/bin ...
The file "coraenv" already exists in /usr/local/bin. Overwrite it? (y/n)
[n]: y
Copying coraenv to /usr/local/bin ...
Entries will be added to the /etc/oratab file as needed by
Database Configuration Assistant when a database is created
Finished running generic part of root script.
Now product-specific root actions will be performed.
Using configuration parameter file:
/u01/app/12.1.0/grid_1/crs/install/crsconfig_params
2014/05/23 00:19:09 CLSRSC-363: User ignored prerequisites during
installation
ASM upgrade has started on first node.
OLR initialization - successful
2014/05/23 00:24:23 CLSRSC-329: Replacing Clusterware entries in file
'oracle-ohasd.conf'
CRS-4133: Oracle High Availability Services has been stopped.
CRS-4123: Oracle High Availability Services has been started.
2014/05/23 00:29:05 CLSRSC-343: Successfully started Oracle clusterware
stack
clscfg: EXISTING configuration version 5 detected.
clscfg: version 5 is 11g Release 2.
Successfully accumulated necessary OCR keys.
Creating OCR keys for user 'root', privgrp 'root'..
Operation successful.
2014/05/23 00:33:31 CLSRSC-325: Configure Oracle Grid Infrastructure for
a Cluster ... succeeded
[[email protected] bin]#
On oel61b
[[email protected] ~]# /u01/app/12.1.0/grid_1/rootupgrade.sh
Performing root user operation for Oracle 12c
The following environment variables are set as:
ORACLE_OWNER= grid
ORACLE_HOME= /u01/app/12.1.0/grid_1
Enter the full pathname of the local bin directory: [/usr/local/bin]:
The file "dbhome" already exists in /usr/local/bin. Overwrite it? (y/n)
[n]: y
Copying dbhome to /usr/local/bin ...
The file "oraenv" already exists in /usr/local/bin. Overwrite it? (y/n)
[n]: y
Copying oraenv to /usr/local/bin ...
The file "coraenv" already exists in /usr/local/bin. Overwrite it? (y/n)
[n]: y
Copying coraenv to /usr/local/bin ...
Entries will be added to the /etc/oratab file as needed by
Database Configuration Assistant when a database is created
Finished running generic part of root script.
Now product-specific root actions will be performed.
Using configuration parameter file:
/u01/app/12.1.0/grid_1/crs/install/crsconfig_params
2014/05/23 00:37:21 CLSRSC-363: User ignored prerequisites during
installation
OLR initialization - successful
2014/05/23 00:40:39 CLSRSC-329: Replacing Clusterware entries in file
'oracle-ohasd.conf'
CRS-4133: Oracle High Availability Services has been stopped.
CRS-4123: Oracle High Availability Services has been started.
2014/05/23 00:44:27 CLSRSC-343: Successfully started Oracle clusterware
stack
clscfg: EXISTING configuration version 5 detected.
clscfg: version 5 is 12c Release 1.
Successfully accumulated necessary OCR keys.
Creating OCR keys for user 'root', privgrp 'root'..
Operation successful.
Start upgrade invoked..
Started to upgrade the Oracle Clusterware. This operation may take a few
minutes.
Started to upgrade the OCR.
The OCR was successfully upgraded.
Started to upgrade the CSS.
The CSS was successfully upgraded.
Started to upgrade Oracle ASM.
Started to upgrade the CRS.
The CRS was successfully upgraded.
Oracle Clusterware operating version was successfully set to 12.1.0.1.0
2014/05/23 00:53:16 CLSRSC-325: Configure Oracle Grid Infrastructure for
a Cluster ... succeeded
[[email protected] ~]#
Wait for the assistants to complete
Review the Cluster Verification Utility
[[email protected] grid_1]# grep ERR
/u01/app/oraInventory/logs/installActions2014-05-22_10-39-26PM.log
INFO: ERROR: [Result.addErrorDescription:607] PRVF -7530 : Sufficient
physical memory is not available on node "oel61b" [Required physical
memory = 4GB (4194304.0KB)]
INFO: ERROR: [Result.addErrorDescription:607] PRVF -7530 : Sufficient
physical memory is not available on node "oel61a" [Required physical
memory = 4GB (4194304.0KB)]
ERRORMSG(oel61b): PRVF-7530 : Sufficient physical memory is not
available on node "oel61b" [Required physical memory = 4GB (4194304.0KB)]
ERRORMSG(oel61a): PRVF-7530 : Sufficient physical memory is not
available on node "oel61a" [Required physical memory = 4GB (4194304.0KB)]
INFO: ERROR: [Result.addErrorDescription:607] PRVF -5636 : The DNS
response time for an unreachable node exceeded "15000" ms on following
nodes: oel61a,oel61b
INFO: ERROR: [Result.addErrorDescription:607] PRVF -5636 : The DNS
response time for an unreachable node exceeded "15000" ms on following
nodes: oel61a,oel61b
ERRORMSG(oel61b): PRVF-5636 : The DNS response time for an
unreachable node exceeded "15000" ms on following nodes: oel61a,oel61b
ERRORMSG(oel61a): PRVF-5636 : The DNS response time for an
unreachable node exceeded "15000" ms on following nodes: oel61a,oel61b
INFO: ERROR: [Result.addErrorDescription:618] PRVF -5636 : The DNS
response time for an unreachable node exceeded "15000" ms on following
nodes: oel61a,oel61b
INFO: ERROR: [Result.addErrorDescription:618] PRVF -5636 : The DNS
response time for an unreachable node exceeded "15000" ms on following
nodes: oel61a,oel61b
INFO: ERROR: [Result.addErrorDescription:607] Check for integrity of
file "/etc/resolv.conf" failed
INFO: ERROR: [Result.addErrorDescription:607] Check for integrity of
file "/etc/resolv.conf" failed
ERRORMSG(oel61b): PRVF-5636 : The DNS response time for an
unreachable node exceeded "15000" ms on following nodes: oel61a,oel61b
ERRORMSG(oel61b): Check for integrity of file
"/etc/resolv.conf" failed
ERRORMSG(oel61a): PRVF-5636 : The DNS response time for an
unreachable node exceeded "15000" ms on following nodes: oel61a,oel61b
ERRORMSG(oel61a): Check for integrity of file
"/etc/resolv.conf" failed
INFO: ERROR: [Result.addErrorDescription:607] PRVG -1359 : Daemon process
"avahi-daemon" is configured on node "oel61b"
INFO: ERROR: [Result.addErrorDescription:607] PRVG -1359 : Daemon process
"avahi-daemon" is configured on node "oel61a"
INFO: ERROR: [Result.addErrorDescription:618] PRVG -1359 : Daemon process
"avahi-daemon" is configured on node "oel61b"
INFO: ERROR: [Result.addErrorDescription:618] PRVG -1359 : Daemon process
"avahi-daemon" is configured on node "oel61a"
INFO: ERROR: [Result.addErrorDescription:607] PRVG-1360 : Daemon process
"avahi-daemon" is running on node "oel61b"
INFO: ERROR: [Result.addErrorDescription:607] PRVG -1360 : Daemon process
"avahi-daemon" is running on node "oel61a"
INFO: ERROR: [Result.addErrorDescription:618] PRVG -1360 : Daemon process
"avahi-daemon" is running on node "oel61b"
INFO: ERROR: [Result.addErrorDescription:618] PRVG -1360 : Daemon process
"avahi-daemon" is running on node "oel61a"
ERRORMSG(oel61b): PRVG-1359 : Daemon process "avahi-daemon" is
configured on node "oel61b"
ERRORMSG(oel61b): PRVG-1360 : Daemon process "avahi-daemon" is
running on node "oel61b"
ERRORMSG(oel61a): PRVG-1359 : Daemon process "avahi-daemon" is
configured on node "oel61a"
ERRORMSG(oel61a): PRVG-1360 : Daemon process "avahi-daemon" is
running on node "oel61a"
INFO: ERROR:
[[email protected] grid_1]#
2.15
Verify GI installation
[[email protected] bin]# ./crsctl check cluster -all
**************************************************************
oel61a:
CRS-4537: Cluster Ready Services is online
CRS-4529: Cluster Synchronization Services is online
CRS-4533: Event Manager is online
**************************************************************
oel61b:
CRS-4537: Cluster Ready Services is online
CRS-4529: Cluster Synchronization Services is online
CRS-4533: Event Manager is online
**************************************************************
[[email protected] bin]# ./crsctl stat res -t
------------------------------------------------------------------------------Name
Target State
Server
State
details
------------------------------------------------------------------------------Local Resources
------------------------------------------------------------------------------ora.DATA.dg
ONLINE ONLINE
oel61a
STABLE
ONLINE ONLINE
oel61b
STABLE
ora.LISTENER.lsnr
ONLINE ONLINE
oel61a
STABLE
ONLINE ONLINE
oel61b
STABLE
ora.asm
ONLINE ONLINE
oel61a
Started,STABLE
ONLINE ONLINE
oel61b
STABLE
ora.net1.network
ONLINE ONLINE
oel61a
STABLE
ONLINE ONLINE
oel61b
STABLE
ora.ons
ONLINE ONLINE
oel61a
STABLE
ONLINE ONLINE
oel61b
STABLE
ora.registry.acfs
ONLINE OFFLINE
oel61a
STABLE
ONLINE OFFLINE
oel61b
STABLE
------------------------------------------------------------------------------Cluster Resources
------------------------------------------------------------------------------ora.LISTENER_SCAN1.lsnr
1
ONLINE ONLINE
oel61b
STABLE
ora.LISTENER_SCAN2.lsnr
1
ONLINE ONLINE
oel61a
STABLE
ora.LISTENER_SCAN3.lsnr
1
ONLINE ONLINE
oel61a
STABLE
ora.MGMTLSNR
1
ONLINE ONLINE
oel61a
169.254.46.130 10.10
.2.21
10.10.10.21,ST
ABLE
ora.cvu
1
ONLINE ONLINE
oel61b
STABLE
ora.gns
1
ONLINE ONLINE
oel61a
STABLE
ora.gns.vip
1
ONLINE ONLINE
oel61a
STABLE
ora.mgmtdb
1
ONLINE ONLINE
oel61a
Open,STABLE
ora.oc4j
1
ONLINE ONLINE
oel61b
STABLE
ora.oel61a.vip
1
ONLINE ONLINE
oel61a
STABLE
ora.oel61b.vip
1
ONLINE ONLINE
oel61b
STABLE
ora.racdb.db
1
ONLINE ONLINE
oel61a
Open,STABLE
2
ONLINE OFFLINE
Instance
Shutdown,ST
ABLE
ora.racdb.racdbsrv.svc
1
ONLINE ONLINE
oel61a
STABLE
2
ONLINE OFFLINE
STABLE
ora.scan1.vip
1
ONLINE ONLINE
oel61b
STABLE
ora.scan2.vip
1
ONLINE ONLINE
oel61a
STABLE
ora.scan3.vip
1
ONLINE ONLINE
oel61a
STABLE
------------------------------------------------------------------------------[[email protected] bin]#
2.16
2.17
This concludes the Grid Infrastructure Upograde from 11.2.0.3 to 12c
12.1.0.1
Install Oracle 12c RDBMS binaries in a separate $OH.
Run OUI from 12c database stage directory.
Select Skip updates
Select Install software only
Select RAC database installation.
Select All Nodes
Select languages
Select Enterprise Edition
Verify the locations.
Verify OS groups.
Review
The errors are as follows
Task resolv.conf Integrity - This task checks consistency of file
/etc/resolv.conf file across nodes
Check Failed on Nodes: [oel61b, oel61a]
Verification result of failed node: oel61b Details:
PRVF-5636 : The DNS response time for an unreachable node exceeded
"15000" ms on following nodes: oel61a,oel61b - Cause: The DNS response
time for an unreachable node exceeded the value specified on nodes
specified. - Action: Make sure that 'options timeout', 'options
attempts' and 'nameserver' entries in file resolv.conf are proper. On
HPUX these entries will be 'retrans', 'retry' and 'nameserver'. On
Solaris these will be 'options retrans', 'options retry' and
'nameserver'. Make sure that the DNS server responds back to name lookup
request within the specified time when looking up an unknown host name.
Check for integrity of file "/etc/resolv.conf" failed - Cause: Cause Of
Problem Not Available - Action: User Action Not Available
Back to Top
Verification result of failed node: oel61a Details:
PRVF-5636 : The DNS response time for an unreachable node exceeded
"15000" ms on following nodes: oel61a,oel61b - Cause: The DNS response
time for an unreachable node exceeded the value specified on nodes
specified. - Action: Make sure that 'options timeout', 'options
attempts' and 'nameserver' entries in file resolv.conf are proper. On
HPUX these entries will be 'retrans', 'retry' and 'nameserver'. On
Solaris these will be 'options retrans', 'options retry' and
'nameserver'. Make sure that the DNS server responds back to name lookup
request within the specified time when looking up an unknown host name.
Check for integrity of file "/etc/resolv.conf" failed - Cause: Cause Of
Problem Not Available - Action: User Action Not Available
Back to Top
Single Client Access Name (SCAN) - This test verifies the Single Client
Access Name configuration. Error:
PRVG-1101 : SCAN name "oel61-cluster-scan.gns.grid.gj.com" failed to
resolve - Cause: An attempt to resolve specified SCAN name to a list of
IP addresses failed because SCAN could not be resolved in DNS or GNS
using 'nslookup'. - Action: Check whether the specified SCAN name is
correct. If SCAN name should be resolved in DNS, check the configuration
of SCAN name in DNS. If it should be resolved in GNS make sure that GNS
resource is online.
PRVG-1101 : SCAN name "oel61-cluster-scan.gns.grid.gj.com" failed to
resolve - Cause: An attempt to resolve specified SCAN name to a list of
IP addresses failed because SCAN could not be resolved in DNS or GNS
using 'nslookup'. - Action: Check whether the specified SCAN name is
correct. If SCAN name should be resolved in DNS, check the configuration
of SCAN name in DNS. If it should be resolved in GNS make sure that GNS
resource is online.
Check Failed on Nodes: [oel61b, oel61a]
Verification result of failed node: oel61b Back to Top
Verification result of failed node: oel61a Back to Top
For PRVF-5636 Look at : PRVF-5636 : The DNS response time for an unreachable
node exceeded "15000" ms on following nodes (Doc ID 1356975.1)
For PRVG-1101 Do the following
Before:
[[email protected] ~]$ cluvfy comp gns -postcrsinst -verbose
Verifying GNS integrity
Checking GNS integrity...
Checking if the GNS subdomain name is valid...
The GNS subdomain name "gns.grid.gj.com" is a valid domain name
Checking if the GNS VIP belongs to same subnet as the public network...
Public network subnets "192.168.2.0, 192.168.2.0, 192.168.2.0,
192.168.2.0, 192.168.2.0" match with the GNS VIP "192.168.2.0,
192.168.2.0, 192.168.2.0, 192.168.2.0, 192.168.2.0"
Checking if the GNS VIP is a valid address...
GNS VIP "192.168.2.52" resolves to a valid IP address
Checking the status of GNS VIP...
Checking if FDQN names for domain "gns.grid.gj.com" are reachable
WARNING:
PRVF-5218 : "oel61a-vip.gns.grid.gj.com" did not resolve into any IP
address
PRVF-5827 : The response time for name lookup for name "oel61avip.gns.grid.gj.com" exceeded 15 seconds
WARNING:
PRVF-5218 : "oel61b-vip.gns.grid.gj.com" did not resolve into any IP
address
PRVF-5827 : The response time for name lookup for name "oel61bvip.gns.grid.gj.com" exceeded 15 seconds
Checking status of GNS resource...
Node
Running?
Enabled?
------------ ------------------------ -----------------------oel61a
yes
yes
oel61b
no
yes
GNS resource configuration check passed
Checking status of GNS VIP resource...
Node
Running?
------------ -----------------------oel61a
yes
oel61b
no
Enabled?
-----------------------yes
yes
GNS VIP resource configuration check passed.
GNS integrity check failed
Verification of GNS integrity was unsuccessful on all the specified
nodes.
[[email protected] ~]$
Make sure that the GNS static VIP address is in /etc/resolv.conf.
Note that if NetwokManager is running the file content is
overridden.
[[email protected] bin]# cat cat /etc/resolv.conf
cat: cat: No such file or directory
# Generated by NetworkManager
search gj.com
nameserver 192.168.2.1
nameserver 192.168.2.11
nameserver 192.168.2.52
[[email protected] bin]#
[[email protected] bin]# cat /etc/resolv.conf
# Generated by NetworkManager
search gj.com
nameserver 192.168.2.11
nameserver 192.168.2.1
nameserver 192.168.2.52
[[email protected] bin]#
After the modification we get
[[email protected] dbs]$ nslookup oel61-cluster-scan.gns.grid.gj.com
Server:
192.168.2.52
Address:
192.168.2.52#53
Name:
oel61-cluster-scan.gns.grid.gj.com
Address: 192.168.2.117
Name: oel61-cluster-scan.gns.grid.gj.com
Address: 192.168.2.111
Name: oel61-cluster-scan.gns.grid.gj.com
Address: 192.168.2.112
[[email protected] dbs]$
[[email protected] ~]$ nslookup oel61 -cluster-scan.gns.grid.gj.com
Server:
192.168.2.52
Address:
192.168.2.52#53
Name: oel61-cluster-scan.gns.grid.gj.com
Address: 192.168.2.117
Name: oel61-cluster-scan.gns.grid.gj.com
Address: 192.168.2.111
Name: oel61-cluster-scan.gns.grid.gj.com
Address: 192.168.2.112
[[email protected] ~]$ cluvfy comp gns -postcrsinst -verbose
Verifying GNS integrity
Checking GNS integrity...
Checking if the GNS subdomain name is valid...
The GNS subdomain name "gns.grid.gj.com" is a valid domain name
Checking if the GNS VIP belongs to same subnet as the public network...
Public network subnets "192.168.2.0, 192.168.2.0, 192.168.2.0" match with
the GNS VIP "192.168.2.0, 192.168.2.0, 192.168.2.0"
Checking if the GNS VIP is a valid address...
GNS VIP "192.168.2.52" resolves to a valid IP address
Checking the status of GNS VIP...
Checking if FDQN names for domain "gns.grid.gj.com" are reachable
GNS resolved IP addresses are reachable
GNS resolved IP addresses are reachable
GNS resolved IP
Checking status
Node
-----------oel61a
oel61b
addresses are reachable
of GNS resource...
Running?
-----------------------yes
no
Enabled?
-----------------------yes
yes
GNS resource configuration check passed
Checking status of GNS VIP resource...
Node
Running?
------------ -----------------------oel61a
yes
oel61b
no
Enabled?
-----------------------yes
yes
GNS VIP resource configuration check passed.
GNS integrity check passed
Verification of GNS integrity was successful.
[[email protected] ~]$
Select Ignore All
Wait until prompted for the actions that need to be ran as root.
Run the scripts
[[email protected] bin]# /u01/app/oracle/product/12.1.0/db_1/root.sh
Performing root user operation for Oracle 12c
The following environment variables are set as:
ORACLE_OWNER= oracle
ORACLE_HOME= /u01/app/oracle/product/12.1.0/db_1
Enter the full pathname of the local bin directory: [/usr/local/bin]:
The contents of "dbhome" have not changed. No need to overwrite.
The contents of "oraenv" have not changed. No need to overwrite.
The contents of "coraenv" have not changed. No need to overwrite.
Entries will be added to the /etc/oratab file as needed by
Database Configuration Assistant when a database is created
Finished running generic part of root script.
Now product-specific root actions will be performed.
[[email protected] bin]#
[[email protected] ~]# /u01/app/oracle/product/12.1.0/db_1/root.sh
Performing root user operation for Oracle 12c
The following environment variables are set as:
ORACLE_OWNER= oracle
ORACLE_HOME= /u01/app/oracle/product/12.1.0/db_1
Enter the full pathname of the local bin directory: [/usr/local/bin]:
The contents of "dbhome" have not changed. No need to overwrite.
The contents of "oraenv" have not changed. No need to overwrite.
The contents of "coraenv" have not changed. No need to overwrite.
Entries will be added to the /etc/oratab file as needed by
Database Configuration Assistant when a database is created
Finished running generic part of root script.
Now product-specific root actions will be performed.
[[email protected] ~]#
Edit OUI
2.18
From the OLD $OH make sure that database is started and FRA is large
enough and you db_recovery_file_dest_size sized appropriately.
SQL> alter system set db_recovery_file_dest_size=60G scope=both sid='*';
System altered.
SQL>
2.19
Run dbua
Take a Note that dbua makes a convenient backup that you can use for
recovery if something goes wrong. For you to take advantage of this
option you need to select it on the dbua before you start. I
strongly recommend using it. I had a problem with the
db_recovery_file_dest_size set too low and had to restore and re-try.
Invoke dbua from the new 12c $OH
Select Upgrade Oracle Database.
Select the database, review and press Next.
Wait for the prerequisites check to complete.
Examine the findings. This particular one is fixable so press Next
to continue.
Note here is where you specify the backup option, some parallelism
options, statistics gathering prior to the upgrade etc. If something
goes wrong a script will wait for you in the specified location for
restore.
Select an option for EM Express
Note here is where you specify the backup location. If something
goes wrong a script will wait for you in the specified location for
restore.
You should not get this is FRA is big enough. If you are stuck
restore the database to a state to before the upgrade. Fix whatever
the problem is and retry.
Review the summary
Review the actions
Wait for the upgrade to complete.
At the end of the upgrade you can have something like this.
View the results and close dbua.
2.20
Verify that database is successfully upgraded.
[[email protected] ~]$ srvctl config database -d racdb
Database unique name: RACDB
Database name: RACDB
Oracle home: /u01/app/oracle/product/12.1.0/db_1
Oracle user: oracle
Spfile: +DATA/racdb/spfileracdb.ora
Password file:
Domain:
Start options: open
Stop options: immediate
Database role: PRIMARY
Management policy: AUTOMATIC
Server pools: servpool
Database instances:
Disk Groups: DATA
Mount point paths:
Services: racdbsrv
Type: RAC
Start concurrency:
Stop concurrency:
Database is policy managed
[[email protected] ~]$
[[email protected] admin]$ srvctl status database -d racdb
Instance RACDB_1 is running on node oel61b
Instance RACDB_2 is running on node oel61a
[[email protected] admin]$ sqlplus / as sysdba
SQL*Plus: Release 12.1.0.1.0 Production on Sat May 24 22:59:37 2014
Copyright (c) 1982, 2013, Oracle.
All rights reserved.
Connected to:
Oracle Database 12c Enterprise Edition Release 12.1.0.1.0 - 64bit
Production
With the Partitioning, Real Application Clusters, Automatic Storage
Management, OLAP,
Advanced Analytics and Real Application Testing options
SQL> select * from v$active_instances;
INST_NUMBER
----------INST_NAME
------------------------------------------------------------------------------CON_ID
---------1
oel61b.gj.com:RACDB_1
0
2
oel61a.gj.com:RACDB_2
0
INST_NUMBER
----------INST_NAME
------------------------------------------------------------------------------CON_ID
---------SQL> set linesize 300
SQL> /
INST_NUMBER INST_NAME
CON_ID
----------- --------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- ---------1 oel61b.gj.com:RACDB_1
0
2 oel61a.gj.com:RACDB_2
0
SQL>
SQL> select * from gv$instance;
INST_ID INSTANCE_NUMBER INSTANCE_NAME
HOST_NAME
VERSION
STARTUP_T STATUS
PAR
THREAD# ARCHIVE LOG_SWITCH_WAIT LOGINS SHU DATABASE_STATUS
INSTANCE_ROLE ACTIVE_ST BLO
CON_ID INSTANCE_MO EDITION
---------- --------------- ---------------- --------------------------------------------------------------- ----------------- --------- ----------- --- ---------- ------- --------------- ---------- --- ---------------- ------------------ --------- --- ---------- ----------- ------FAMILY
------------------------------------------------------------------------------2
2 RACDB_2
oel61a.gj.com
12.1.0.1.0
24-MAY-14 OPEN
YES
2
STARTED
ALLOWED NO ACTIVE
PRIMARY_INSTANCE
NORMAL
NO
0 REGULAR
EE
1
STARTED
NORMAL
NO
1 RACDB_1
oel61b.gj.com
12.1.0.1.0
24-MAY-14 OPEN
ALLOWED NO ACTIVE
0 REGULAR
EE
YES
1
PRIMARY_INSTANCE
SQL>
[[email protected] ~]$ crsctl stat res -t
------------------------------------------------------------------------------Name
Target State
Server
State
details
------------------------------------------------------------------------------Local Resources
------------------------------------------------------------------------------ora.DATA.dg
ONLINE ONLINE
oel61a
STABLE
ONLINE ONLINE
oel61b
STABLE
ora.LISTENER.lsnr
ONLINE ONLINE
oel61a
STABLE
ONLINE ONLINE
oel61b
STABLE
ora.asm
ONLINE ONLINE
oel61a
Started,STABLE
ONLINE ONLINE
oel61b
Started,STABLE
ora.net1.network
ONLINE ONLINE
oel61a
STABLE
ONLINE ONLINE
oel61b
STABLE
ora.ons
ONLINE ONLINE
oel61a
STABLE
ONLINE ONLINE
oel61b
STABLE
ora.registry.acfs
ONLINE OFFLINE
oel61a
STABLE
ONLINE OFFLINE
oel61b
STABLE
------------------------------------------------------------------------------Cluster Resources
------------------------------------------------------------------------------ora.LISTENER_SCAN1.lsnr
1
ONLINE ONLINE
oel61a
STABLE
ora.LISTENER_SCAN2.lsnr
1
ONLINE ONLINE
oel61b
STABLE
ora.LISTENER_SCAN3.lsnr
1
ONLINE ONLINE
oel61b
STABLE
ora.MGMTLSNR
1
ONLINE ONLINE
oel61b
169.254.81.184 10.10
.10.22
10.10.5.22,ST
ABLE
ora.cvu
1
ONLINE ONLINE
oel61b
STABLE
ora.gns
1
ONLINE ONLINE
oel61b
STABLE
ora.gns.vip
1
ONLINE ONLINE
oel61b
STABLE
ora.mgmtdb
1
ONLINE ONLINE
oel61b
Open,STABLE
ora.oc4j
1
ONLINE ONLINE
oel61b
STABLE
ora.oel61a.vip
1
ONLINE ONLINE
oel61a
STABLE
ora.oel61b.vip
1
ONLINE ONLINE
oel61b
STABLE
ora.racdb.db
1
ONLINE ONLINE
oel61b
Open,STABLE
2
ONLINE ONLINE
oel61a
Open,STABLE
ora.racdb.racdbsrv.svc
1
ONLINE ONLINE
oel61a
STABLE
2
ONLINE ONLINE
oel61b
STABLE
ora.scan1.vip
1
ONLINE ONLINE
oel61a
STABLE
ora.scan2.vip
1
ONLINE ONLINE
oel61b
STABLE
ora.scan3.vip
1
ONLINE ONLINE
oel61b
STABLE
------------------------------------------------------------------------------[[email protected] ~]$
2.21
Handy and Useful script to recover the database in case of failed
upgrade.
[[email protected] RACDB]# cd backup
[[email protected] backup]# pwd
/u01/app/oracle/admin/RACDB/backup
[[email protected] backup]# ls
createSPFile_RACDB.sql
ctl_backup_1400922874007
RACDB_2_restore.sh
ctl_backup_1400807180325 df_backup_01p8voqo_1_1
rmanRestoreCommands_RACDB
[[email protected] backup]# cat createSPFile_RACDB.sql
connect / as sysdba
df_backup_04p93abe_1_1
init.ora
CREATE SPFILE='+DATA/racdb/spfileracdb.ora' from
pfile='/u01/app/oracle/admin/RACDB/backup/init.ora';
exit;
[[email protected] backup]# cat RACDB_2_restore.sh
#!/bin/sh
# -- Run this Script to Restore Oracle Database Instance RACDB_2
echo -- Shutting down the database from the new oracle home ...
ORACLE_HOME=/u01/app/oracle/product/12.1.0/db_1; export ORACLE_HOME
/u01/app/oracle/product/12.1.0/db_1/bin/srvctl stop database -d RACDB
echo -- Downgrading the database CRS resources ...
echo y | /u01/app/oracle/product/12.1.0/db_1/bin/srvctl downgrade database d RACDB -t 11.2.0.3.0 -o /u01/app/oracle/product/11.2.0/db_1
ORACLE_HOME=/u01/app/oracle/product/11.2.0/db_1; export ORACLE_HOME
ORACLE_SID=RACDB_2; export ORACLE_SID
echo y | /u01/app/oracle/product/11.2.0/db_1/bin/srvctl modify database -d
RACDB -p +DATA/RACDB/spfileRACDB.ora
echo -- Removing /u01/app/oracle/cfgtooll ogs/dbua/logs/Welcome_RACDB_2.txt
file
rm -f /u01/app/oracle/cfgtoollogs/dbua/logs/Welcome_RACDB_2.txt ;
/u01/app/oracle/product/11.2.0/db_1/bin/sqlplus /nolog
@/u01/app/oracle/admin/RACDB/backup/createSPFile_RACDB.sql
/u01/app/oracle/product/11.2.0/db_1/bin/rman
@/u01/app/oracle/admin/RACDB/backup/rmanRestoreCommands_RACDB
echo -- Starting up the database from the old oracle home ...
/u01/app/oracle/product/11.2.0/db_1/bin/srvctl start database -d RACDB
[[email protected] backup]#
[[email protected] backup]# cat rmanRestoreCommands_RACDB
connect target /;
startup nomount;
set nocfau;
restore controlfile from
'/u01/app/oracle/admin/RACDB/backup/ctl_backup_1400922874007';
alter database mount;
restore database;
alter database open resetlogs;
exit
[[email protected] backup]#
2.22
This conclude the database upgrade from 11.2.0.3 to 12c (12.1.0.1)
Annex A
Cluvfy output
[[email protected] grid]$ ./runcluvfy.sh stage -pre crsinst -n oel61a,oel61b
Performing pre-checks for cluster services setup
Checking node reachability...
Node reachability check passed from node "oel61a"
Checking user equivalence...
User equivalence check passed for user "grid"
Checking node connectivity...
Checking hosts config file...
Verification of the hosts config file successful
Check: Node connectivity using interfaces on subnet "192.168.2.0"
Node connectivity passed for subnet "192.168.2.0" with node(s)
oel61b,oel61a
TCP connectivity check passed for subnet "192.168.2.0"
Check: Node connectivity using interfaces on subnet "10.10.10.0"
Node connectivity passed for subnet "10.10.10.0" with node(s)
oel61b,oel61a
TCP connectivity check passed for subnet "10.10.10.0"
Check: Node connectivity using interfaces on subnet "10.10.2.0"
Node connectivity passed for subnet "10.10.2.0" with node(s)
oel61a,oel61b
TCP connectivity check passed for subnet "10.10.2.0"
Check: Node connectivity using interfaces on subnet "10.10.5.0"
Node connectivity passed for subnet "10.10.5.0" with node(s)
oel61b,oel61a
TCP connectivity check passed for subnet "10.10.5.0"
Checking subnet mask consistency...
Subnet mask consistency check passed for
Subnet mask consistency check passed for
Subnet mask consistency check passed for
Subnet mask consistency check passed for
Subnet mask consistency check passed.
subnet
subnet
subnet
subnet
"10.10.2.0".
"192.168.2.0".
"10.10.10.0".
"10.10.5.0".
Node connectivity check passed
Checking multicast communication...
Checking subnet "10.10.2.0" for multicast communication with multicast
group "224.0.0.251"...
Check of subnet "10.10.2.0" for multicast communication with multicast
group "224.0.0.251" passed.
Checking subnet "10.10.10.0" for multicast communication with multicast
group "224.0.0.251"...
Check of subnet "10.10.10.0" for multicast communication with multicast
group "224.0.0.251" passed.
Checking subnet "10.10.5.0" for multicast communication with multicast
group "224.0.0.251"...
Check of subnet "10.10.5.0" for multicast communication with multicast
group "224.0.0.251" passed.
Check of multicast communication passed.
Checking ASMLib configuration.
Check for ASMLib configuration passed.
Total memory check failed
Check failed on nodes:
oel61b,oel61a
Available memory check passed
Swap space check passed
Free disk space check passed for "oel61b:/usr"
Free disk space check passed for "oel61a:/usr"
Free disk space check passed for "oel61b:/var"
Free disk space check passed for "oel61a:/var"
Free disk space check passed for "oel61b:/etc,oel61b:/sbin"
Free disk space check passed for "oel61a:/etc,oel61a:/sbin"
Free disk space check passed for "oel61b:/u01/app/11.2.0/grid"
Free disk space check passed for "oel61a:/u01/app/11.2.0/grid"
Free disk space check passed for "oel61b:/tmp"
Free disk space check passed for "oel61a:/tmp"
Check for multiple users with UID value 1100 passed
User existence check passed for "grid"
Group existence check passed for "oinstall"
Group existence check passed for "dba"
Membership check for user "grid" in group "oinstall" [as Primary] passed
Membership check for user "grid" in group "dba" passed
Run level check passed
Hard limits check passed for "maximum open file descriptors"
Soft limits check passed for "maximum open file descriptors"
Hard limits check passed for "maximum user processes"
Soft limits check passed for "maximum user processes"
System architecture check passed
Kernel version check passed
Kernel parameter check passed for "semmsl"
Kernel parameter check passed for "semmns"
Kernel parameter check passed for "semopm"
Kernel parameter check passed for "semmni"
Kernel parameter check passed for "shmmax"
Kernel parameter check passed for "shmmni"
Kernel parameter check passed for "shmall"
Kernel parameter check passed for "file-max"
Kernel parameter check passed for "ip_local_port_range"
Kernel parameter check passed for "rmem_default"
Kernel parameter check passed for "rmem_max"
Kernel parameter check passed for "wmem_default"
Kernel parameter check passed for "wmem_max"
Kernel parameter check passed for "aio-max-nr"
Package existence check passed for "binutils"
Package existence check passed for "compat-libcap1"
Package existence check passed for "compat-libstdc++-33(x86_64)"
Package existence check passed for "libgcc(x86_64)"
Package existence check passed for "libstdc++(x86_64)"
Package existence check passed for "libstdc++-devel(x86_64)"
Package existence check passed for "sysstat"
Package existence check passed for "gcc"
Package existence check passed for "gcc-c++"
Package existence check passed for "ksh"
Package existence check passed for "make"
Package existence check passed for "glibc(x86_64)"
Package existence check passed for "glibc -devel(x86_64)"
Package existence check passed for "libaio(x86_64)"
Package existence check passed for "libaio-devel(x86_64)"
Package existence check passed for "nfs-utils"
Check for multiple users with UID value 0 passed
Current group ID check passed
Starting check for consistency of primary group of root user
Check for consistency of root user's primary group passed
Starting Clock synchronization checks using Network Time Protocol(NTP)...
NTP Configuration file check started...
No NTP Daemons or Services were found to be running
Clock synchronization check using Network Time Protocol(NTP) passed
Core file name pattern consistency check passed.
User "grid" is not part of "root" group. Check passed
Default user file creation mask check passed
Checking integrity of file "/etc/resolv.conf" across nodes
"domain" and "search" entries do not coexist in any "/etc/resolv.conf"
file
All nodes have same "search" order defined in file "/etc/resolv.conf"
PRVF-5636 : The DNS response time for an unreachable node exceeded
"15000" ms on following nodes: oel61a,oel61b
Check for integrity of file "/etc/resolv.conf" failed
Time zone consistency check passed
Checking integrity of name service switch configuration file
"/etc/nsswitch.conf" ...
All nodes have same "hosts" entry defined in file "/etc/nsswitch.conf"
Check for integrity of name service switch configuration file
"/etc/nsswitch.conf" passed
Checking daemon "avahi-daemon" is not configured and running
Daemon not configured check failed for process "avahi-daemon"
Check failed on nodes:
oel61b,oel61a
Daemon not running check failed for process "avahi-daemon"
Check failed on nodes:
oel61b,oel61a
Starting check for Reverse path filter setting ...
Check for Reverse path filter setting passed
Starting check for /dev/shm mounted as temporary file system ...
Check for /dev/shm mounted as temporary file system passed
Pre-check for cluster services setup was unsuccessful on all the nodes.
[[email protected] grid]$
[[email protected] grid]$ ./runcluvfy.sh stage -post hwos -n oel61a,oel61b
Performing post-checks for hardware and operating system setup
Checking node reachability...
Node reachability check passed from node "oel61a"
Checking user equivalence...
User equivalence check passed for user "grid"
Checking node connectivity...
Checking hosts config file...
Verification of the hosts config file successful
Check: Node connectivity using interfaces on subnet "192.168.2.0"
Node connectivity passed for subnet "192.168.2.0" with node(s)
oel61b,oel61a
TCP connectivity check passed for subnet "192.168.2.0"
Check: Node connectivity using interfaces on subnet "10.10.10.0"
Node connectivity passed for subnet "10.10.10.0" with node(s)
oel61a,oel61b
TCP connectivity check passed for subnet "10.10.10.0"
Check: Node connectivity using interfaces on subnet "10.10.2.0"
Node connectivity passed for subnet "10.10.2.0" with node(s)
oel61b,oel61a
TCP connectivity check passed for subnet "10.10.2.0"
Check: Node connectivity using interfaces on subnet "10.10.5.0"
Node connectivity passed for subnet "10.10.5.0" with node(s)
oel61b,oel61a
TCP connectivity check passed for subnet "10.10.5.0"
Checking subnet mask consistency...
Subnet mask consistency check passed for
Subnet mask consistency check passed for
Subnet mask consistency check passed for
Subnet mask consistency check passed for
Subnet mask consistency check passed.
subnet
subnet
subnet
subnet
"10.10.2.0".
"192.168.2.0".
"10.10.10.0".
"10.10.5.0".
Node connectivity check passed
Checking multicast communication...
Checking subnet "10.10.2.0" for multicast communication with multicast
group "224.0.0.251"...
Check of subnet "10.10.2.0" for multicast communication with multicast
group "224.0.0.251" passed.
Checking subnet "10.10.10.0" for multicast communication with multicast
group "224.0.0.251"...
Check of subnet "10.10.10.0" for multicast communication with multicast
group "224.0.0.251" passed.
Checking subnet "10.10.5.0" for multicast communication with multicast
group "224.0.0.251"...
Check of subnet "10.10.5.0" for multicast communication with multicast
group "224.0.0.251" passed.
Check of multicast communication passed.
Check for multiple users with UID value 0 passed
Time zone consistency check passed
Checking shared storage accessibility...
ASM Disk Group
-----------------------------------DATA
Sharing Nodes (2 in count)
-----------------------oel61a oel61b
Disk
-----------------------------------/dev/sde
Sharing Nodes (2 in count)
-----------------------oel61a oel61b
Disk
-----------------------------------/dev/sde1
Sharing Nodes (2 in count)
-----------------------oel61a oel61b
Disk
-----------------------------------/dev/sdf
Sharing Nodes (2 in count)
-----------------------oel61a oel61b
Disk
-----------------------------------/dev/sdf1
Sharing Nodes (2 in count)
-----------------------oel61a oel61b
Disk
-----------------------------------/dev/sdb
Sharing Nodes (2 in count)
-----------------------oel61a oel61b
Disk
-----------------------------------/dev/sdb1
Sharing Nodes (2 in count)
-----------------------oel61a oel61b
Disk
-----------------------------------/dev/sdd
Sharing Nodes (2 in count)
-----------------------oel61a oel6 1b
Disk
-----------------------------------/dev/sdd1
Sharing Nodes (2 in count)
-----------------------oel61a oel61b
Disk
-----------------------------------/dev/sdc
Sharing Nodes (2 in count)
-----------------------oel61a oel61b
Disk
-----------------------------------/dev/sdc1
Sharing Nodes (2 in count)
-----------------------oel61a oel61b
Shared storage check was successful on nodes "oel61a,oel61b"
Checking integrity of name service switch configuration file
"/etc/nsswitch.conf" ...
All nodes have same "hosts" entry defined in file "/etc/nsswitch.conf"
Check for integrity of name service switch configuration file
"/etc/nsswitch.conf" passed
Post-check for hardware and operating system setup was successful.
[[email protected] grid]$
MAKE SURE THE CLUSTER IS UP AND RUNNING
[[email protected] bin]# ./crsctl check cluster -all
**************************************************************
oel61a:
CRS-4537: Cluster Ready Services is online
CRS-4529: Cluster Synchronization Services is online
CRS-4533: Event Manager is online
**************************************************************
oel61b:
CRS-4537: Cluster Ready Services is online
CRS-4529: Cluster Synchronization Services is online
CRS-4533: Event Manager is online
**************************************************************
[[email protected] bin]# ./crsctl stat res -t
------------------------------------------------------------------------------NAME
TARGET STATE
SERVER
STATE_DETAILS
-------------------------------------------------------- ----------------------Local Resources
------------------------------------------------------------------------------ora.DATA.dg
ONLINE ONLINE
oel61a
ONLINE ONLINE
oel61b
ora.LISTENER.lsnr
ONLINE ONLINE
oel61a
ONLINE ONLINE
oel61b
ora.asm
ONLINE ONLINE
oel61a
Started
ONLINE ONLINE
oel61b
Started
ora.gsd
OFFLINE OFFLINE
oel61a
OFFLINE OFFLINE
oel61b
ora.net1.network
ONLINE ONLINE
oel61a
ONLINE ONLINE
oel61b
ora.ons
ONLINE ONLINE
oel61a
ONLINE ONLINE
oel61b
ora.registry.acfs
ONLINE OFFLINE
oel61a
ONLINE OFFLINE
oel61b
------------------------------------------------------------------------------Cluster Resources
------------------------------------------------------------------------------ora.LISTENER_SCAN1.lsnr
1
ONLINE ONLINE
oel61a
ora.LISTENER_SCAN2.lsnr
1
ONLINE ONLINE
oel61b
ora.LISTENER_SCAN3.lsnr
1
ONLINE ONLINE
oel61b
ora.cvu
1
ONLINE ONLINE
oel61b
ora.gns
1
ONLINE ONLINE
oel61b
ora.gns.vip
1
ONLINE ONLINE
oel61b
ora.oc4j
1
ONLINE ONLINE
oel61b
ora.oel61a.vip
1
ONLINE ONLINE
oel61a
ora.oel61b.vip
1
ONLINE ONLINE
oel61b
ora.racdb.db
1
ONLINE ONLINE
oel61a
Open
2
ONLINE ONLINE
oel61b
Open
ora.racdb.racdbsrv.svc
1
ONLINE
2
ONLINE
ora.scan1.vip
1
ONLINE
ora.scan2.vip
1
ONLINE
ora.scan3.vip
1
ONLINE
[[email protected] bin]#
ONLINE
ONLINE
oel61a
oel61b
ONLINE
oel61a
ONLINE
oel61b
ONLINE
oel61b
BASH PROFILES
[[email protected] ~]$ cat .bash_profile
# .bash_profile
umask 022
ORACLE_BASE=/u01/app/oracle
ORACLE_HOME=/u01/app/oracle/product/12.1.0/db_1
#ORACLE_HOME=/u01/app/oracle/product/11.2.0/db_1
ORACLE_HOSTNAME=oel61a
ORACLE_SID=RACDB_2
ORACLE_UNQNAME=RACDB
LD_LIBRARY_PATH=$ORACLE_HOME/lib
PATH=$PATH:$ORACLE_HOME/bin
export ORACLE_BASE ORACLE_HOME ORACLE_SID LD_LIBRARY_PATH PATH
ORACLE_HOSTNAME ORACLE_UNQNAME
TEMP=/tmp
TMPDIR=/tmp
export TEMP TMPDIR
ulimit -t unlimited
ulimit -f unlimited
ulimit -d unlimited
#ulimit -s unlimited
ulimit -v unlimited
ulimit -n 36500
if [ -t 0 ]; then
stty intr ^C
fi
# Get the aliases and functions
if [ -f ~/.bashrc ]; then
. ~/.bashrc
fi
# User specific environment and startup programs
PATH=$PATH:$HOME/bin
export PATH
# Get the aliases and functions
if [ -f ~/.bashrc ]; then
. ~/.bashrc
fi
# User specific environment and startup programs
PATH=$PATH:$HOME/bin
export PATH
[[email protected] ~]$
[[email protected] ~]$ cat .bash_profile
# .bash_profile
# Get the aliases and functions
if [ -f ~/.bashrc ]; then
. ~/.bashrc
fi
umask 022
ORACLE_BASE=/u01/app/grid
ORACLE_HOME=/u01/app/12.1.0/grid_1
ORACLE_HOSTNAME=oel61a
ORACLE_SID=+ASM1
LD_LIBRARY_PATH=$ORACLE_HOME/lib
PATH=$PATH:$ORACLE_HOME/bin
export ORACLE_BASE ORACLE_HOME ORACLE_SID LD_LIBRARY_PATH PATH
ORACLE_HOSTNAME
TEMP=/tmp
TMPDIR=/tmp
export TEMP TMPDIR
ulimit -t unlimited
ulimit -f unlimited
ulimit -d unlimited
ulimit -s unlimited
ulimit -v unlimited
if [ -t 0 ]; then
stty intr ^C
fi
# Get the aliases and functions
if [ -f ~/.bashrc ]; then
. ~/.bashrc
fi
# User specific environment and startup programs
PATH=$PATH:$HOME/bin
export PATH
# User specific environment and startup programs
PATH=$PATH:$HOME/bin
export PATH
[[email protected] ~]$
[[email protected] ~]# su - oracle
[[email protected] ~]$ cat .bash_profile
# .bash_profile
umask 022
ORACLE_BASE=/u01/app/oracle
ORACLE_HOME=/u01/app/oracle/product/12.1.0/db_1
ORACLE_HOSTNAME=oel61b
ORACLE_SID=RACDB_1
ORACLE_UNQNAME=RACDB
LD_LIBRARY_PATH=$ORACLE_HOME/lib
PATH=$PATH:$ORACLE_HOME/bin
export ORACLE_BASE ORACLE_HOME ORACLE_SID LD_LIBRARY_PATH PATH
ORACLE_HOSTNAME ORACLE_UNQNAME
TEMP=/tmp
TMPDIR=/tmp
export TEMP TMPDIR
ulimit -t unlimited
ulimit -f unlimited
ulimit -d unlimited
#ulimit -s 65000
ulimit -v unlimited
ulimit -n 32560
if [ -t 0 ]; then
stty intr ^C
fi
# Get the aliases and functions
if [ -f ~/.bashrc ]; then
. ~/.bashrc
fi
# User specific environment and startup programs
PATH=$PATH:$HOME/bin
export PATH
# Get the aliases and functions
if [ -f ~/.bashrc ]; then
. ~/.bashrc
fi
# User specific environment and startup programs
PATH=$PATH:$HOME/bin
export PATH
[[email protected] ~]$
[[email protected] ~]# su - oracle
[[email protected] ~]$ cat .bash_profile
# .bash_profile
umask 022
ORACLE_BASE=/u01/app/oracle
ORACLE_HOME=/u01/app/oracle/product/12.1.0/db_1
ORACLE_HOSTNAME=oel61b
ORACLE_SID=RACDB_1
ORACLE_UNQNAME=RACDB
LD_LIBRARY_PATH=$ORACLE_HOME/lib
PATH=$PATH:$ORACLE_HOME/bin
export ORACLE_BASE ORACLE_HOME ORACLE_SID LD_LIBRARY_PATH PATH
ORACLE_HOSTNAME ORACLE_UNQNAME
TEMP=/tmp
TMPDIR=/tmp
export TEMP TMPDIR
ulimit -t unlimited
ulimit -f unlimited
ulimit -d unlimited
#ulimit -s 65000
ulimit -v unlimited
ulimit -n 32560
if [ -t 0 ]; then
stty intr ^C
fi
# Get the aliases and functions
if [ -f ~/.bashrc ]; then
. ~/.bashrc
fi
# User specific environment and startup programs
PATH=$PATH:$HOME/bin
export PATH
# Get the aliases and functions
if [ -f ~/.bashrc ]; then
. ~/.bashrc
fi
# User specific environment and startup programs
PATH=$PATH:$HOME/bin
export PATH
[[email protected] ~]$ exit
logout
[[email protected] ~]# su - grid
[[email protected] ~]$ cat .bash_profile
# .bash_profile
# Get the aliases and functions
if [ -f ~/.bashrc ]; then
. ~/.bashrc
fi
umask 022
ORACLE_BASE=/u01/app/grid
ORACLE_HOME=/u01/app/12.1.0/grid_1
ORACLE_HOSTNAME=oel61b
ORACLE_SID=+ASM2
LD_LIBRARY_PATH=$ORACLE_HOME/lib
PATH=$PATH:$ORACLE_HOME/bin
export ORACLE_BASE ORACLE_HOME ORACLE_SID LD_LIBRARY_PATH PATH
ORACLE_HOSTNAME
TEMP=/tmp
TMPDIR=/tmp
export TEMP TMPDIR
ulimit -t unlimited
ulimit -f unlimited
ulimit -d unlimited
ulimit -s unlimited
ulimit -v unlimited
ulimit -n 32560
if [ -t 0 ]; then
stty intr ^C
fi
# Get the aliases and functions
if [ -f ~/.bashrc ]; then
. ~/.bashrc
fi
# User specific environment and startup programs
PATH=$PATH:$HOME/bin
export PATH
# User specific environment and startup programs
PATH=$PATH:$HOME/bin
export PATH
[[email protected] ~]$