INSTALLATION GUIDE APPLICATION Plug And Play Conversion kit for 75154-01A 1 19-03969-90L Wire harness 2 16-03970-90 ODB II Plug AMP Part # 3 x2 76400-01A 19-0POSITWIST Posi-Twist™ NOTE: This install sheet is to be used in Conjuntion with the 75154-01A. This sheet will replace steps 8-41 of your install sheet. AMP RESEARCH TECH SUPPORT 1-888-983-2204 (Press 2) Monday - Friday, 6:00 AM - 5:00 PM PST Invented, engineered and manufactured exclusively by AMP Research in the USA. May be covered by one of the following patents: 6,641,158; 6,830,257; 6,834,875; 6,938,909; 7,055,839; 7,380,807; 7,398,985; 7,584,975 ©2012 AMP Research. All rights reserved. Printed in USA. www.amp-research.com /4 IM76400 rev 03.17.14 A M P R E S E A R C H P O W E R S T E P TM – C H E V R O L E T / G M C This install will replace steps 8-41 from your 75154-01A install sheet. Using the two 11” cable ties, mount controller to support arm next to battery. Plug in harness (Ensure that locking tabs engage) 5 19 1 Remove power fuse. Attach power lead (RED wire) to positive pole on the battery. Attach ground lead to negative battery pole. CAUTION: Do not ground wrench when engaged with nut. Route long end of wire harness above engine and Pull up front door sill plate covers as shown. down through drivers side wheel well. Zip tie harness to cowling clips on fire wall. Route short end down passengers side. 4 3 2 1 2 3 Pull up the carpet and drill 9/32” hole in metal and insert supplied rubber grommet (21). Route wire harness along the frame and back towards 4 Secure with zip ties. Push both wires rear linkages. through rubber grommets. 4 2 NOTE: Seal holes with silicone glue and cover with tape so carpet does not stick to glue. 4 5 www.amp-research.com 5 6 /4 IM76154 rev 02.05.14 A M P R E S E A R C H P O W E R S T E P TM – C H E V R O L E T / G M C OBD II install: Use Supplied Posi Twist connectors to attach the Plug and Play Module to the Harness. Attach matching colors on the harness to the wires on the module. Plug in module to OBD II port on the vehicle. Secure harness with supplied tie wraps. Note: If the OBD II pass thru harness (76404-01A) was purchased see install sheet supplied in packaging. 8 10 4 6 6 Continue with step 42 from your 75154-01A Install sheet for the remainder of the install. 11 6 10 www.amp-research.com /4 IM76400 rev 03.17.14 ™ Congratulations on your purchase of the genuine AMP Research PowerStep! Here’s what you should know... AMP Research PowerStep running boards automatically move when the doors are opened to assist entering and exiting the vehicle. Automatic power deploy: The running boards will extend down and out when the doors are opened. Automatic power stow: The running boards will return to the stowed position when the doors are closed. There will be a 2-second delay before the running boards move to the stowed position. Automatic stop: If an object is in the way of the moving running board, the running board will automatically stop. To reset, clear any obstruction, then simply open and close the door to resume normal operation. Manually set in the deployed (OUT) position for access to the roof: your foot while at the same time closing the door. To resume normal operation, open and close the door. Maintenance: In adverse conditions, debris such as mud, dirt, and salt may become trapped in the running board mechanism, possibly leading to unwanted noise. If this occurs, manually set the running boards to Avoid spraying the motors directly. After washing, apply silicone spray lubricant to the hinge pivot pins. Do not apply silicone, wax or protectants like Armor All® to the running board stepping surface. Caution! Keep hands away when the running board is in motion. 5-YEAR LIMITED WARRANTY AMP RESEARCH warrants this product to be free from defects in material and workmanship for FIVE (5) YEARS FROM DATE OF PURCHASE, provided there has been normal use and proper maintenance. This warranty applies to the original purchaser only. All remedies under this warranty are limited to the repair replacement of the product itself, or the repair or replacement of any component part thereof, found by the factory to be defective within the time period specified. The decision to repair or replace is wholly within the discretion of the manufacturer. for instructions. You must retain proof of purchase and submit a copy with any items returned for warranty work. Upon completion of warranty work, if any, we will return the repaired or replaced item or items to you freight prepaid. Damage to our products caused by accidents, fire, vandalism, negligence, misinstallation, misuse, Acts of God, or by defective parts not manufactured by us, is not covered under this warranty. ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE CREATED HEREBY ARE LIMITED IN DURATION TO THE SAME DURATION AND SCOPE AS THE EXPRESS WRITTEN WARRANTY. OUR COMPANY SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGE. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state. FOR WARRANTY ISSUES WITH THIS PRODUCT PLEASE CALL AMP RESEARCH CUSTOMER SERVICE 1-888-983-2204 WARNING Be sure to read and precisely follow the provided instructions when installing this product. Failure to do so could place the vehicle occupants in a potentially dangerous situation. After installing or reinstalling, re-check to insure that the product is properly installed.
© Copyright 2018 ExploreDoc