PFD7CN-3

Installation and Operation Instructions
Before attempting to connect or operate this product, please
read these instructions completely.
PFD7CN-3
SView™ Outdoor Pressurized FusionDome Camera System
PFD7CN-3.................IP Network Ready 7” Pressurized Outdoor PTZ Camera System with 23x zoom compression, full D1. Clear dome, with 24Vac input, heater / blower
PFD7CS-3.................(Analog version)
IP Network Ready 7” Pressurized Outdoor PTZ Camera System with 23x zoom compression, full D1. Clear dome, with 24Vac input,
heater / blower
Moog Inc.
Sensor and Surveillance Systems
© 2013, Moog Inc. All Rights Reserved
3650 Woodhead Drive Northbrook, IL. USA 60062
+1.847.498.0700 Fax: +1.847.498.1258 www.moogS3.com
81-IN5382 111113
IMPORTANT SAFEGUARDS
1
Read these instructions.
2
Keep these instructions.
3
Heed all warnings
4
Follow all instructions.
5
Do not use this apparatus near water.
6
Clean only with damp cloth.
7
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Do not block any of the ventilation openings. Install in accordance with the
manufacturers instructions.
8
9
SAFETY PRECAUTIONS
Cable Runs- All cable runs must be within permissible distance.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER ( OR BACK). NO USER- SERVICEABLE PARTS INSIDE. REFER SEVICING
TO QUALIFIED SERVICE PERSONNEL.
Mounting - This unit must be properly and securely mounted to a supporting
structure capable of sustaining the weight of the unit.
Accordingly:
a. This installation should be made by a qualified service person and should conform
to all local codes.
b. Care should be exercised to select suitable hardware to install the unit, taking into
account both the composition of the mounting surface and the weight of the unit.
10 Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus ( including amplifiers) that produce heat.
11 Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. When the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
12 Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
13 Only use attachment/ accessories specified by the manufacturer.
14 Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
15 Unplug this apparatus during lighting storms or when unused for long periods of time.
16 Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled of objects have fallen into the apparatus, the
The lightning flash with an arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of non-insulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk to persons.
Este símbolo se piensa para alertar al usuario a la presencia
del “voltaje peligroso no-aisIado” dentro del recinto de los
productos que puede ser un riesgo de choque eléctrico.
Ce symbole est prévu pour alerter I’utilisateur à la presence
“de la tension dangereuse” non-isolée dans la clôture de
produits qui peut être un risque de choc électrique.
Dieses Symbol soll den Benutzer zum Vorhandensein der
nicht-lsolier “Gefährdungsspannung” innerhalb der
Produkteinschließung alarmieren die eine Gefahr des
elektrischen Schlages sein kann.
Este símbolo é pretendido alertar o usuário à presença “di
tensão perigosa non-isolada” dentro do cerco dos produtos
que pode ser um risco de choque elétrico.
Questo simbolo è inteso per avvertire I’utente alla presenza
“di tensione pericolosa” non-isolata all’interno della
recinzione dei prodotti che può essere un rischio di scossa
elettrica.
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
Be sure to periodically examine the unit and the supporting structure to make sure that the integrity
of the installation is intact. Failure to comply with the foregoing could result in the unit separating
from the support structure and falling, with resultant damages or injury to anyone or anything struck
by the falling unit.
UNPACKING
Unpack carefully. Electronic components can be
damaged if improperly handled or dropped. If an item
appears to have been damaged in shipment, replace
it properly in its carton and notify the shipper.
Be sure to save:
1 The shipping carton and packaging material.
They are the safest material in which to make future
shipments of the equipment.
2 These Installation and Operating Instructions.
SERVICE
If technical support or service is needed, contact us at
the following number:
TECHNICAL SUPPORT
AVAILABLE 24 HOURS
1 - 800 - 554 -1124
The exclamation point within an equilateral
triangle is intended to alert the user to
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
Este símbolo del punto del exclamation se piensa para
alertar al usuario a la presencia de instrucciones importantes
en la literatura que acompaña la aplicación.
Ce symbole de point d’exclamation est prévu pour alerter
l’utilisateur à la presence des instructions importantes dans
la littérature accompagnant l’appareil.
Dieses Ausruf Punktsymbol soll den Benutzer zum
Vorhandensein de wichtigen Anweisungen in der Literatur
alarmieren, die das Gerät begleitet.
Este símbolo do ponto do exclamation é pretendido alertar o
usuário à presença de instruções importantes na literatura
que acompanha o dispositivo.
Questo simbolo del punto del exclamaton è inteso per
avvertire l’utente alla presenza delle istruzioni importanti nella
letteratura che accompagna l'apparecchio.
MADEIN
USA
BUY AMERICA COMPLIANT • COUNTRY OF ORIGIN U.S.A.
Product Warranty Registration
Register Your Products Online
www.moogS3.com/technical-support/product-registration
Moog values your patronage. We are solely committed to providing you with the highest quality products and
superior customer service. With 3-Year and 5-Year warranties (depending on the product purchased) we stand
behind every product we sell.
See full warranty details at www.moogS3.com/technical-support/warranty-plan/
:
• Simple and Trouble-Free RMA process
• Product / software updates
• Special promotions
• Eliminate the need to archive purchase documents such as receipts, purchase orders, etc.
Limited Warranty for Moog Products
Moog - Decatur Operations, subsequently referred to as “Manufacturer,” warrants these products to be free from defects in material or workmanship as follows:
PRODUCT CATEGORY
PARTS \ LABOR
All Enclosures and Electronics
Five (5) Years
Accessory Brackets
Five (5) Years
Controllers
Three (3) Years
Power Supplies / IR Illuminators
Three (3) Years
Poles / PolEvators / CamEvator
Three (3) Years
Warrior Series™ / Q-View™
Three (3) Years
™
Three (3) Years 6 months if used in auto scan / tour operation
SView Series
™
DeputyDome , NiteTrac , Igloo Dome, PurgeDome
Three (3) Years 6 months if used in auto scan / tour operation
EXO Series™ Dome and Fixed Camera Systems*
Three (3) Years 6 months if used in auto scan / tour operation
EXO Series™ GeminEye Visible and Thermal Camera Systems
One (1) Year
™
™
™
During the labor warranty period, to repair the Product, Purchaser will either return the defective product, freight prepaid, or deliver it to Manufacturer at Moog Decatur
Operations, 2525 Park Central Boulevard, Decatur, Georgia, 30035. The Product to be repaired is to be returned in either its original carton or a similar package affording
an equal degree of protection with a RMA # (Return Materials Authorization number) displayed on the outer box or packing slip. To obtain a RMA# you must contact our
Technical Support Team at 800.554.1124, extension 101. Manufacturer will return the repaired product freight prepaid to Purchaser. Manufacturer is not obligated to
provide Purchaser with a substitute unit during the warranty period or at any time. After the applicable warranty period, Purchaser must pay all labor and/or parts charges.
The limited warranty stated in these product instructions is subject to all of the following terms and conditions.
TERMS AND CONDITIONS
1. NOTIFICATION OF CLAIMS: WARRANTY SERVICE: If Purchaser believes that the Product is defective in material or workmanship, then written notice with an explanation
of the claim shall be given promptly by Purchaser to Manufacturer. All claims for warranty service must be made within the warranty period. If after investigation,
Manufacturer determines the reported problem was not covered by the warranty, Purchaser shall pay Manufacturer for the cost of investigating the problem at its then
prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall extend the warranty period of the entire Product. The specific warranty on
the repaired part only shall be in effect for a period of ninety (90) days following the repair or replacement of that part or the remaining period of the Product parts warranty,
whichever is greater.
2. EXCLUSIVE REMEDY: ACCEPTANCE: Purchaser’s exclusive remedy and Manufacturer’s sole obligation is to supply (or pay for) all labor necessary to repair any Product
found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts.
3. EXCEPTIONS TO LIMITED WARRANTY: Manufacturer shall have no liability or obligation to Purchaser with respect to any Product requiring service during the warranty
period which is subjected to any of the following: abuse, improper use, negligence, accident, or acts of God (i.e., hurricanes, earthquakes), modification, failure of the
end-user to follow the directions outlined in the product instructions, failure of the end-user to follow the maintenance procedures recommended by the International Security
Industry Organization, written in product instructions, or recommended in the service manual for the Product. Furthermore, Manufacturer shall have no liability where a
schedule is specified for regular replacement or maintenance or cleaning of certain parts (based on usage) and the end-user has failed to follow such schedule; attempted
repair by non-qualified personnel; operation of the Product outside of the published environmental and electrical parameters, or if such Product’s original identification
(trademark, serial number) markings have been defaced, altered, or removed. Manufacturer excludes from warranty coverage Products sold AS IS and/or WITH ALL FAULTS
and excludes used Products which have not been sold by Manufacturer to the Purchaser. All software and accompanying documentation furnished with, or as part of the
Product is furnished “AS IS” (i.e., without any warranty of any kind), except where expressly provided otherwise in any documentation or license agreement furnished with
the Product. ANY COST ASSOCIATED WITH REMOVAL OF DEFECTIVE PRODUCT AND INSTALLATION OF REPLACEMENT PRODUCT IS NOT INCLUDED IN THIS WARRANTY.
4. PROOF OF PURCHASE: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.
DISCLAIMER OF WARRANTY
EXCEPT FOR THE FOREGOING WARRANTIES, MANUFACTURER HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY WARRANTY WITH REGARD TO ANY
CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL CODE AND/OR IN ANY OTHER COMPARABLE STATE STATUTE.
MANUFACTURER HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-MANUFACTURER
PRODUCTS OR NON-MANUFACTURER RECOMMENDED PRODUCTS PURCHASER MAY CHOOSE TO CONNECT TO THE PRODUCT.
LIMITATION OF LIABILITY
THE LIABILITY OF Manufacturer, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER, REGARDLESS
OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE PRODUCT WITH RESPECT
TO WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL MANUFACTURER BE LIABLE TO PURCHASER FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION, REPLACEMENT LABOR COSTS, REIMBURSEMENT, OR DAMAGES ON ACCOUNT OF THE LOSS
OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.
* NOTE
Moog will repair or replace, at its option, any equipment which is damaged by transient voltage surge/spike or lightning strike (an “Occurrence”), while properly connected
to wired AC power line with protective ground. Any repair or modification of the equipment done by someone other than Moog voids the warranty.
Form 500-911 081913
!
English
Electrical Specifications
Power 24VAC
Class 2 Only
Contents of Box
PFD7CN-3
PFD7CS-3
24 VAC
3.3 Amps
Total Power: 80 Watts
Accessories:
Heater: 50 Watts/Blower: 2 Watts
Camera Power:
28 Watts
Tools Required:
.100” Flat Head Screwdriver
Phillips Head Screwdriver
7/16” Wrench or Socket
24 VAC
3.3 amperios
Energía Total: 80 vatios
Accesorios:
Calentador: 50 Watts/Blower: 2 vatio
Energía De la Cámara fotográfica:
28 vatios
Español
Las Herramientas Requirieron: Destornillador Principal Plano Del 100"
Destornillador Principal Phillips
Français
24 VCA
3.3 ampères
Puissance Totale : 80 watts
Accessoires :
Réchauffeur : 50 Watts/Blower : 2 watts
Puissance D'Appareil-photo :
28 watts
Les Outils besoin :
Tournevis Principal Plat De 100"
Tournevis Principal Phillips
Deutsch
24 VAC
3.3 Ampere
Gesamtenergie: 80 Watt
Zusatzgeräte:
Heizung: 50 Watt/Blower: 2 Watt
Kamera-Energie:
28 Watt
Werkzeuge Erforderten: 100"Flacher Hauptschraubenzieher
Kreuzkopfhauptschraubenzieher
24 VAC
3.3 ampères
Poder Total: 80 watts
Acessórios:
Poder Da Câmera:
Portuguese
Italiano
Calefator: 50 Watts/Blower: 2 watt
28 watt
As Ferramentas Requereram: Chave de fenda Principal Lisa Do 100"
Chave de fenda Principal Phillips
24 VAC
3.3 ampère
Alimentazione Totale: 80 watt
Accessori:
Riscaldatore: 50 Watts/Blower: 2 watt
Alimentazione Della Macchina fotografica:
28 watt
Attrezzi Richiesti:
Cacciavite Capo Piano Del 100"
Cacciavite Capo "phillips"
*** Pan Tilt boxed separately along with its instructions.
WM20G: SOLD SEPARATELY
12
2
1
SOLD SEPARATELY
•Special anti-seize tape
“DO NOT REMOVE”
Teflon tape™ is wrapped around the pipe threads to
ensure a tight seal and to prevent galling.
• Cinta de Teflon ™ se envuelve alrededor de las roscas de la tubería para
asegurar un sello hermético y para evitar el gripado.
• Ruban téflon ™ est enroulé autour des filetages pour assurer une bonne
étanchéité et éviter tout grippage.
• Teflonband ™ ist rund um die Rohrgewinde gewickelt, um eine Abdichtung
zu gewährleisten und zu verhindern Fressen.
• Fita de Teflon ™ é enrolado em torno das roscas do tubo para assegurar uma
selagem apertada e para evitar escoriações.
• Teflon ™ nastro è avvolto intorno le filettature per assicurare una buona tenuta
e per prevenire l'usura.
3
SOLD SEPARATELY
Screw the coupling tightly onto the pipe threads by
inserting a screwdriver through slots in coupling to
ease in final tightening.
Securely mount bracket to wall. Pull wiring
through bracket and position grommet as shown.
• Con seguridad soporte del montaje a emparedar. Tire del cableado
a través del soporte y del ojal de la posición según lo demostrado.
• Solidement parenthèse de bâti à murer. Tirez le câblage par la
parenthèse et le canon isolant de position comme montré.
• Sicher Einfassung Haltewinkel wall. Ziehen Sie Verdrahtung durch
Haltewinkel und Position Gummimuffe, wie gezeigt.
• Firmemente suporte da montagem a wall. Puxe a fiação através do
suporte e do ilhó da posição como mostrado.
• Saldamente staffa del supporto da wall. Tiri i collegamenti tramite la
staffa ed il gommino di protezione di posizione come indicato.
4
SOLD SEPARATELY
Screw the (2) bolts into the coupling.
•
Atornillar el acoplamiento firmemente en las roscas de las tuberías mediante la inserción de un
destornillador a través de las ranuras de acoplamiento para facilitar el apriete final.
• Atornille (2) los pernos en el acoplador.
•
Vissez le couplage serré sur le filetage de tuyaux en insérant un tournevis dans les fentes de
couplage à l'aise dans le serrage final.
• Vissez (2) les boulons dans l'accouplement.
•
Schrauben Sie die Kupplung fest auf die Rohrgewinde durch Einführen eines Schraubendrehers
durch die Schlitze in der Kopplung in dem endgültigen Anziehen zu erleichtern.
• Schrauben Sie die (2) Schraubbolzen in die
Koppelung.
•
Parafuse o acoplamento bem para as roscas pela inserção de uma chave de fenda através
ranhuras para facilitar o acoplamento no aperto final.
• Parafuse (2) os parafusos no acoplamento.
•
Avvitare l'attacco saldamente sulle filettature inserendo un cacciavite nelle fessure di
accoppiamento ad allentarsi nel serraggio finale.
• Avviti (2) i bulloni nell'accoppiamento.
5
SOLD SEPARATELY
SOLD SEPARATELY
Make the appropriate wiring connections
from the dome to the pendant.
Loop the lanyard over the screw
head to temporarily hold housing.
• Loop la cuerda de seguridad en la cabeza del tornillo para mantener
temporalmente la vivienda.
• Enroulez le cordon autour de la tête de vis pour maintenir temporairement
le logement.
• Loop the Lanyard über den Schraubenkopf vorübergehend zu
halten Gehäuse.
• Laço da corda sobre a cabeça do parafuso para reter
temporariamente habitação.
• Avvolgere il cordino sulla testa della vite per memorizzare
temporaneamente alloggi.
7
6
SOLD SEPARATELY
• Hacer las conexiones de cableado de la cúpula de la
pendiente.
• Faites le câblage de la coupole de la suspension.
• Nehmen Sie die entsprechenden Kabel-Verbindungen von der
Kuppel auf den Anhänger.
• Faça as conexões de cabos da cúpula para o pingente.
• Apportare le opportune connessioni cablaggio dalla cupola a
ciondolo.
8
SOLD SEPARATELY
•Locking Screws
•Third Anti-Twist
Screw
Undo the lanyard, push housing up and twist. Secure
with the (2) locking bolts and washers. Add third
anti-twist screw if so equipped.
• Deshacer la cuerda de seguridad, empuje y gire hasta la vivienda. Asegure con los
tornillos de bloqueo (2) y las arandelas. Añadir tercero anti-torsión del tornillo si lo tiene.
• Défaire le cordon, appuyer sur le logement et torsion. Fixer avec les vis de blocage (2)
et les rondelles. Ajouter troisième anticorps anti-torsion vis si équipé.
• Lösen Sie die Leine, drücken Gehäuse und Touch. Sichern Sie mit den (2) Verriegelung
Schrauben und Unterlegscheiben. Fügen dritten anti-twist Schraube falls vorhanden.
• Desfazer o cordão, empurrar-se de habitação e torcer. Fixe com os parafusos (2) de
fixação e arruelas. Adicionar parafuso anti-torção terceiro se assim equipado.
• Annulla il cordino, spingere abitazioni e torsione. Fissare con le (2) viti di bloccaggio
e le rondelle. Aggiungere un terzo anti-torsione vite se in dotazione.
Slide the grommet down over the coupling to prevent
water from entering and complete the assembly.
• Resbale el ojal abajo sobre el acoplador para evitar que el agua
entre y para terminar a la asamblea.
• Glissez le canon isolant vers le bas au-dessus de l'accouplement
pour empêcher l'eau d'entrer et pour accomplir l'assemblée.
• Schieben Sie die Gummimuffe unten über der Koppelung, um zu
verhindern, daß Wasser und die Versammlung durchzuführen
hereinkommt.
• Deslize o ilhó para baixo sobre o acoplamento para impedir que a
água entre e para terminar o conjunto.
• Faccia scorrere il gommino di protezione giù sopra l'accoppiamento
per impedire l'acqua entrare e per completare il complessivo.
9
10
Wire as shown below for IP
models:(PFD7CN-9; PFD7TN-9)
A
B
A
B
RJ45
24VAC
1 Camera/Heater/Blower
2 Camera/Heater/Blower
SNC-RZ50/SNC-RZ30
Yellow
Green
Wire as shown below for analog
models: (PFD7CS-9; PFD7TS-9)
28 Watts
RJ45
24VAC
1 Camera/Heater/Blower
2 Camera/Heater/Blower
SNC-RZ50/SNC-RZ30
Yellow
Green
13 Watts
52 Watts
52 Watts
C
D
C
1/0
1
2
Alarm 1
Blue
Violet
Common
RJ45
D
Make the appropriate male and female connections. Indoor model does not include pre-run cables.
1/0
1
2
3
4
RS-485RX A
RS-485RX B
RS-485TX A
RS-485TX B
Blue
Violet
Gray
White
RJ45
Make the appropriate male and female connections. Indoor model does not include pre-run cables.
• Haga las conexiones masculinas y femeninas apropiadas. El
modelo de interior no incluye pre-funciona los cables.
• Haga las conexiones masculinas y femeninas apropiadas. El
modelo de interior no incluye pre-funciona los cables.
• Établissez les rapports masculins et femelles appropriés. Le
modèle d'intérieur n'inclut pas pré-courent des câbles.
• Établissez les rapports masculins et femelles appropriés. Le
modèle d'intérieur n'inclut pas pré-courent des câbles.
• Stellen Sie die passenden männlichen und weiblichen
Beziehungen her. Innenmodell schließt nicht vor-laufen lassen
Kabel ein.
• Stellen Sie die passenden männlichen und weiblichen
Beziehungen her. Innenmodell schließt nicht vor-laufen lassen
Kabel ein.
• Faça as conexões masculinas e fêmeas apropriadas. O
modelo indoor não inclui pre-funciona cabos.
• Faça as conexões masculinas e fêmeas apropriadas. O
modelo indoor não inclui pre-funciona cabos.
• Faccia i collegamenti maschii e femminili adatti. Il modello
dell'interno non include pre-fa funzionare i cavi.
• Faccia i collegamenti maschii e femminili adatti. Il modello
dell'interno non include pre-fa funzionare i cavi.
12
11
12
,5
22
,75
20
1,0
18
1,5
16
2,5
14
4
12
6
10
2
MM
AWG
These
are recommended
distances
The
beam
angle may bemaximum
adjusted on
the
for
24VAC
with
a
10%
voltage
drop.
bottom of the unit.
• Éstos se recomiendan las distancias máximas para
24VAC con una gota del voltage del 10%.
• Ceux-ci sont recommandés des distances maximum
pour 24VAC avec une chute de tension de 10%.
• Diese werden maximale Abstände für 24VAC mit
einem 10% Spannungsabfall empfohlen.
• Estes são recomendados distâncias máximas para
24VAC com uma queda de tensão de 10%.
• Questi sono suggeriti distanze massime per 24VAC
con una differenza de potenziale di 10%.
Remove Pan/Tilt from shipping carton.
Install in base bracket in housing.
• Quite Pan/Tilt del cartón del envío. Instale en soporte
bajo en la cubierta.
• Enlevez Pan/Tilt du carton d'expédition. Installez dans
la parenthèse basse dans le logement.
• Entfernen Sie Pan/Tilt vom Verschiffenkarton. Bringen
Sie in niedrigen Haltewinkel im Gehäuse an.
• Remova Pan/Tilt da caixa do transporte. Instale no
suporte baixo na carcaça.
• Rimuova Pan/Tilt dalla scatola di trasporto. Installi in
staffa bassa in alloggiamento.
13
CAPTIVE SCREW
To secure in place, tighten captive screw.
• Para asegurar en lugar, apriete el tornillo prisionero.
• Pour fixer en place, serrez la vis captive.
• Um im Platz zu sichern, ziehen Sie Sicherheitsschraube
fest.
• Para fixar-se no lugar, aperte o parafuso prisioneiro.
• Per fissare sul posto, stringa la vite prigioniera.
15
14
To install the dome align the tabs and twist
counter clockwise to secure.
• Para instalar la bóveda alinee las lengüetas y tuerza al revés
a la derecha para asegurar.
• Pour installer le dôme alignez les étiquettes et tordez contre
dans le sens des aiguilles d'une montre pour fixer.
• Um die Haube anzubringen richten Sie die Vorsprünge aus
und verdrehen Sie sich entgegengesetzt nach rechts um zu
sichern.
• Para instalar a abóbada alinhe as abas e torça-as contra no
sentido horário para fixar-se.
• Per installare la cupola allinei le linguette e torca contro in
senso orario per fissare.
16
100
580
Fitting
50
0
150
Air Chuck
200
250
PSI 300
Hose
Regulator
Nitrogen
Tank
Hand tighten the screws on the dome.
Recommended torque 12 inches/lb (1.35Nm).
• La mano aprieta los tornillos en la bóveda. Esfuerzo de
torsión recomendado 12 inches/lb (el 1.35Nm).
• La main serrent les vis sur le dôme. Couple recommandé 12 inches/lb (1.35Nm).
• Hand ziehen die Schrauben an der Haube fest.
Empfohlene Drehkraft 12 inches/lb (1.35Nm).
• A mão aperta os parafusos na abóbada. Torque
recomendado 12 inches/lb (1.35Nm).
• La mano stringe le viti sulla cupola. Coppia di torsione
suggerita 12 inches/lb (1.35Nm).
When pressurizing unit be sure to set the
gauge or regulator from 10-20psi (.7-1.4bar).
• Al presurizar la unidad esté seguro de fijar el calibrador o
el regulador de 10-20psi (.7-1.4bar).
• En pressurisant l'unité soyez sûr de placer la mesure ou le
régulateur de 10-20psi (.7-1.4bar).
• Wenn Sie Maßeinheit unter Druck setzen, seien
Sie sicher, die Lehre oder den Regler von 10-20psi
(.7-1.4bar) einzustellen.
• Ao pressurizar a unidade seja certo ajustar o calibre ou
o regulador de 10-20psi (.7-1.4bar).
• Nel pressurizzare l'unità sia sicuro regolare il calibro o il
regolatore da 10-20psi (.7-1.4bar).
17
18
Air Chuck
Tank
Valve
Place the air chuck on the tank valve and
begin filling until pressure relief valve opens.
• Coloque la tirada del aire en la válvula del tanque y comience
•
•
•
•
a llenar hasta que la válvula de descarga de presión se abre.
Placez le mandrin d'air sur la valve de réservoir et commencez
à remplir jusqu'à ce que la valve de décompression s'ouvre.
Setzen Sie die Luftklemme auf das Behälterventil und fangen Sie
an zu füllen, bis Druckablaßventil sich öffnet.
Coloque o mandril do ar na válvula do tanque e comece a
encher-se até que a válvula de escape de pressão abra.
Disponga il mandrino dell'aria sulla valvola del carro armato e
cominci a riempirsi fino a che la valvola limitatrice della
pressione non si apra.
12
19
Open the relief valve. Drain all air from the housing and 3
times to remove all moisture.
• Abra la válvula de descarga. Drene todo el aire de la cubierta y
de la repetición 3 times dos veces para quitar toda la humedad.
• Ouvrez la soupape de sécurité. Évacuez tout l'air le logement et la
répétition 3 times pour enlever toute l'humidité.
• Öffnen Sie das Sicherheitsventil. Lassen Sie alle Luft aus dem
Gehäuse und der Wiederholung zweimal ab, um alle Feuchtigkeit
zu entfernen 3 times.
• Abra a válvula de escape. Drene todo o ar da carcaça e do
repeat 3 times para remover toda a umidade.
• Apra la valvola di sfiato. Vuoti due volte tutta l'aria 3 times
dall'alloggiamento e dalla ripetizione per rimuovere tutta l'umidità.
20
10
5
0
The beam angle may be adjusted on the
Power up the unit.
bottom of the unit.
• Energía encima de la unidad.
• Puissance vers le haut de l'unité.
• Energie herauf die Maßeinheit.
• Poder acima da unidade.
• Alimentazione sull'unità.
15
20
25
PSI 30
After purging check the housing pressure. It
should be around 5psi (.34bar).
• Después de purgar el cheque la presión de la cubierta.
Debe estar alrededor de 5psi (34bar).
• Après la purge du contrôle la pression de logement. Elle
devrait être autour de 5psi (34bar).
• Nachdem Überprüfung der Gehäusedruck bereinigt
worden ist. Sie sollte um 5psi (34bar) sein.
• Após ter removido a verificação a pressão da carcaça.
Deve ser em torno de 5psi (34bar).
• Dopo l'eliminazione dell'inceppo del controllo la pressione
dell'alloggiamento. Dovrebbe essere intorno a 5psi
(34bar).
1
Replacement Parts List
PRESSURIZED HOUSING
2
4
3
6
1
5
18
19
7
9
8
17
10
11
15
20
14
12
16
13
21
N/S
21
20
19
18
N/S
N/S
N/S
17
16
15
14
13
12
11
10
9
8
7b
7
6
5
4
3
2
1
WM20G
RP96PSGK08
RP76EN7401
RP76v385A
RPVL2857
RP46PKE1100
RP46PKH2200
RP40CAPPFD811
RPFD080
RPFD060
RPFD050
RP46PKH3063
RPFD072
RP95VALV07
RP95VALV08
RP70PT07a
RP96RSORG10
RPPFDT03
RCTPFD7
RCPFD7
RPPFDTR01
RP96RSORG11
RPVL1795
RPVL1802
RPVL1938
RPPFDT02
Part No.
GOOSE NECK (SOLD SEPARATELY)
P/T Grommet (2)
IP Card
P/T Connection Card (Network Models Only)
P/T Base Bracket
Packet Assembly-Electrical
Packet Assembly-Hardware
External Input Video/Power Cables
Blower
Main Bracket Assembly
Connection PCB
Spacers Packet
24VAC Heater
Tank Valve
5 to 7 psi Pressure Relief Valve
Hermetic Connector, Gasket, Cable
Small O-Ring 4.5"
Internal Sealing Bracket Assembly
Tinted Dome with sealing O-Ring
Clear Dome with sealing O-Ring
Trim Ring w/o Dome
Main O-Ring 9.25"
Tank Valve Gasket
Plastic Rain Shroud
Removable Pendent Coupling
Housing Top (Extended)
Description