MX2010 3D Universal Edge Router Quick Start

MX2010 3D Universal Edge Router
Quick Start
January 2015
Part Number: 530-055063
Revision 01
®
This document describes how to install the Juniper Networks MX2010 3D Universal
Edge Router.
Contents
MX2010 Quick Start Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Step 1: Prepare the Site for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Rack-Mounting Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Moving Requirements and Guidelines Using a Router Transport Kit . . . . . . . . 6
Tools Required to Unpack and Prepare the Router for Installation . . . . . . . . . . 9
Step 2: Install the Mounting Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Install the Mounting Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Step 3: Install the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Unpack the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Remove Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Install the Router Using a Pallet Jack with Attachment . . . . . . . . . . . . . . . . . . 19
Install the Pallet Jack Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Use the Pallet Jack with Attachment to Install the Router . . . . . . . . . . . 20
Install the Router Using a Router Transport Kit . . . . . . . . . . . . . . . . . . . . . . . . 24
Unpack the Router Transport Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Install the Router Transport Kit onto the Router . . . . . . . . . . . . . . . . . . . 26
Secure the Router to the Transport Platform . . . . . . . . . . . . . . . . . . . . . . 28
Use the Router Transport Kit to Install the Router in a Four-Post
Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Use the Router Transport Kit to Install the Router in an Open-Frame
Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Step 4: Connect the Grounding Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Step 5: Reinstall Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Step 6: Connect External Devices and Line Card Cables . . . . . . . . . . . . . . . . . . . . 46
Connect to a Network for Out-of-Band Management . . . . . . . . . . . . . . . . . . 46
Connect a Management Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Connect the Line Card Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Copyright © 2015, Juniper Networks, Inc.
1
MX2010 3D Universal Edge Router Quick Start
Step 7: Connect Power Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Connect Power to a Three-Phase Delta AC Power Distribution Module . . . . 48
Connect Power to a Three-Phase Wye AC Power Distribution Module . . . . . 52
Connect AC Power Supply Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Connect Power to a DC Power Distribution Module . . . . . . . . . . . . . . . . . . . . 58
Connect DC Power Supply Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Step 8: Perform Initial Software Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Enter Configuration Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Configure User Accounts and Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Configure System Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Commit the Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Compliance Statements for NEBS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Compliance Statements for EMC Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
European Community . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Israel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Japan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
United States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Junos OS Documentation and Release Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Requesting Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Self-Help Online Tools and Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Opening a Case with JTAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
2
Copyright © 2015, Juniper Networks, Inc.
MX2010 Quick Start Description
MX2010 Quick Start Description
This Quick Start contains information you need to install and configure the MX2010 3D
Universal Edge Router quickly. For complete installation instructions, see the MX2010 3D
Universal Edge Router Hardware Guide at http://www.juniper.net/techpubs/.
WARNING: This Quick Start contains a summary of safety warnings in “Safety
Warnings” on page 67. For a complete list of warnings for this router, including
translations, see the MX2010 3D Universal Edge Router Hardware Guide at
http://www.juniper.net/techpubs/.
The MX2010 3D Universal Edge Router with the standard or extended cable manager is
34 rack units (U) tall, 59.50 in. (151.13 cm) of rack space. One router with a cable manager
can be installed in a single rack or cabinet.
NOTE: If you are installing the MX2010 router into a network cabinet, make
sure that no hardware, device, rack, or cabinet component obstructs the 34-U
rack space from access during installation.
The MX2010 router has 10 dedicated line card slots, which means a maximum of 10
Modular Port Concentrators (MPCs) housed in adapter cards (ADCs) that can
accommodate Modular Interface Cards (MICs), a host subsystem consisting of 2 Control
Boards with Routing Engines (CB-REs), and 8 Switch Fabric Boards (SFBs).
Adapter cards provide housing to MPCs. The MPCs attach to the adapter cards, which
in turn connect to the backplane.
Up to two MICs can be installed in each MPC. Fully populated, the MX2010 router supports
up to 20 MICs.
For a list of the supported MPCs and MICs, see the MX Series Interface Module Reference.
The router is shipped in a wooden crate, which is bolted securely to a wooden pallet.
Metal latches secure the top and bottom in place. Quick Start installation instructions,
a large rack mount tray, electromagnetic interference (EMI) cover, and a cardboard
accessory box are also included in the shipping container.
NOTE: The shipping container and router (fully populated) weighs
approximately 1343 lb (609.17 kg), depending on your configuration.
Copyright © 2015, Juniper Networks, Inc.
3
MX2010 3D Universal Edge Router Quick Start
Step 1: Prepare the Site for Installation
•
Rack-Mounting Requirements on page 4
•
Moving Requirements and Guidelines Using a Router Transport Kit on page 6
•
Tools Required to Unpack and Prepare the Router for Installation on page 9
Rack-Mounting Requirements
•
You can install the router in an open-frame rack, a four-post rack, or a cabinet.
NOTE: The shipping and installation site must be an ESD-approved area.
•
The rack rails must be spaced widely enough to accommodate the external dimensions
of the router chassis: 59.50 in. (151.13 cm) high, 36.20 in. (91.95 cm) deep, and
19 in. (48.26 cm) wide (see Figure 1 on page 5 and Figure 2 on page 6).
In an open-frame rack, center-mounting is required because the more even distribution
of weight provides greater stability. For center-mounting, you use the mounting brackets
attached to the center of the chassis for rack mounting.
NOTE: The dimensions also include the standard and extended cable
managers and EMI cover.
•
The rack must be able to accommodate the additional depth of the extended cable
manager system, 40.15 in. (102 cm) deep (see Figure 1 on page 5).
•
The rack must be strong enough to support the weight of the fully configured router,
up to 985 lb (446.79 kg).
•
For the cooling system to function properly, the airflow around the chassis must be
unrestricted. Allow at least 36 in. (91.44 cm) of clearance between front-to-rear-cooled
routers. Allow 2.8 in. (7 cm) between the side of the chassis and any non-heat-producing
surface such as a wall.
NOTE: To help redirect exhaust air away from the chassis, there is an
optional adjustable air baffle that can be installed on the upper fan tray
access.
4
•
For service personnel to remove and install hardware components, there must be
adequate space at the front and back of the router. Allow at least 36 in. (91.44 cm) in
front of the router and 36 in. (91.44 cm) behind the router.
•
The rack or cabinet must have an adequate supply of cooling air.
•
Ensure that the cabinet allows the hot exhaust air of the chassis to exit from the cabinet
without recirculating into the router.
Copyright © 2015, Juniper Networks, Inc.
Rack-Mounting Requirements
•
The router must have the shipping covers installed to help move the router into the
rack or cabinet.
•
The router must be installed into a rack or cabinet that is secured to the building
structure.
•
The cabinet must be clear of any hardware, device, rack, or cabinet component that
obstructs the 34-U rack space from being access during installation.
Figure 1: MX2010 Rack Clearance and Router Dimensions for Four-Post
Rack
59.50 in
(151.13 cm)
19.2 in
(48.77 cm)
Copyright © 2015, Juniper Networks, Inc.
36.20 in
(91.95 cm)
g007451
19 in
(48.26 cm)
5
MX2010 3D Universal Edge Router Quick Start
Figure 2: MX2010 Rack Clearance and Router Dimensions for Open-Frame
Rack
59.50 in
(151.13 cm)
36.20 in
(91.95 cm)
19.2 in
(48.77 cm)
g007452
19 in
(48.26 cm)
Moving Requirements and Guidelines Using a Router Transport Kit
The router requires a minimum 42 in. (106.7 cm) diameter of space to turn the chassis
on the router transport kit (see Figure 3 on page 7).
NOTE: The router transport kit handles can be removed to accommodate
aisle width.
6
Copyright © 2015, Juniper Networks, Inc.
Moving Requirements and Guidelines Using a Router Transport Kit
Figure 3: Turning Diameter of Router Transport Kit
g000041
42 in
(106.7 cm)
The weight of the router transport kit is 138.5 lb (63 kg). The maximum recommended
height the router should be lifted from the floor using the router transport kit is 1.5 in.
(3.8 cm).
Viewed from the side, the router with the router transport kit installed measures 59.50 in.
(151.13 cm) high and 36.20 in. (91.95 cm) wide, with the transport kit measuring 23.40 in.
(59.4 cm) high (see Figure 4 on page 8).
Copyright © 2015, Juniper Networks, Inc.
7
MX2010 3D Universal Edge Router Quick Start
Figure 4: Measurements of the Router Transport Kit Installed on the
MX2010 (Side View)
Rear
Front
59.50 in
(151.1 cm)
g000051
23.40 in
(59.4 cm)
36.20 in
(91.95 cm)
Viewed from the front, the router with the router transport kit installed measures 30.78 in.
(78.2 cm) wide (see Figure 5 on page 8).
Figure 5: Measurements of the Router Transport Kit Installed on the
MX2010 (Front View)
30.78 in
(78.2 cm)
8
g000052
19.0 in
(48.26 cm)
Copyright © 2015, Juniper Networks, Inc.
Tools Required to Unpack and Prepare the Router for Installation
Tools Required to Unpack and Prepare the Router for Installation
To unpack the router and prepare for installation, you may need the following tools and
equipment:
•
Standard pallet jack—48 in. (121.92 cm) deep x 27 in. (68.58 cm) wide.
•
Pallet jack attachment (model number MX2000-PLLT-JCK-ADPTR)
•
Router transport kit (model number MX2K-TRNSPRT-KIT)
•
Front component shipping cover
•
Rear component shipping cover
•
Phillips (+) screwdrivers, numbers 1, 2, and 3
•
1/2-in. (12.7 mm) drive ratchet
•
1/4-in. (6.35 mm) torque-controlled driver or socket wrench to tighten the nuts on the
router transport kit
•
1-1/8-in. (28.57 mm) torque-controlled driver or socket wrench to tighten router
transport kit winch mechanism
•
9/16-in. or 14-mm open-end or socket wrench with extension to remove bracket bolts
from the shipping pallet
•
Electrostatic discharge wrist strap
•
Antistatic mat
NOTE: We recommend that you install the MX2010 by using a pallet jack
with attachment or a router transport kit.
Copyright © 2015, Juniper Networks, Inc.
9
MX2010 3D Universal Edge Router Quick Start
Step 2: Install the Mounting Hardware
•
Install the Mounting Hardware on page 10
Install the Mounting Hardware
A mounting shelf is required for installing the router in a four-post rack or cabinet. The
shelf is not required for installing the router in an open-frame rack.
1.
Slide the large shelf between the rack rails, resting the bottom of the shelf on the rack
supports. The large shelf installs on the rear rack rails, extending toward the front of
the rack, as specified in the MX2010 3D Universal Edge Router Hardware Guide, for
large shelf installation.
NOTE: There must be a minimum of 34-U unobstructed front-to-back
usable rack space when installing the MX2010 router into a four-post rack
or cabinet.
2. Partially insert screws into the open holes in the rear flanges of the four-post mounting
shelf (see Figure 6 on page 11).
NOTE: Depending on the type of rack or cabinet you have, cage nuts might
be required.
3. Tighten all the screws completely.
4. On the front of each front rack rail, partially insert a mounting screw into the holes in
each ear of the four-post mounting shelf.
5. Tighten all the screws completely.
10
Copyright © 2015, Juniper Networks, Inc.
Install the Mounting Hardware
Figure 6: Mounting Hardware for a Four-Post Rack or Cabinet
24 in. (60.96 cm)
to 30 in (76.2 cm)
g007101
Front
NOTE: The two rear flanges on the four-post mounting shelf are adjustable
from 24 in. (60.96 cm) through 30 in. (76.2 cm) to accommodate different
types of racks rails.
NOTE: If you are installing the MX2010 router into a network cabinet, make
sure that no hardware, device, rack, or cabinet component obstructs the 34-U
rack space from access during installation.
Copyright © 2015, Juniper Networks, Inc.
11
MX2010 3D Universal Edge Router Quick Start
Step 3: Install the Router
•
Unpack the Router on page 12
•
Remove Components on page 14
•
Install the router using one of the following procedures:
•
Install the Router Using a Pallet Jack with Attachment on page 19
•
Install the Router Using a Router Transport Kit on page 24
•
Unpack the Router on page 12
•
Remove Components on page 14
•
Install the Router Using a Pallet Jack with Attachment on page 19
•
Install the Router Using a Router Transport Kit on page 24
Unpack the Router
The router is shipped in a wooden crate. A wooden pallet forms the base of the crate.
The router chassis is bolted to this pallet. A large rack mount tray, pallet jack attachment,
EMI cover, and a cardboard accessory box are also included in the shipping crate.
Before removing the router from the shipping crate, you must remove all components
(see “Remove Components” on page 14).
Because of the router’s size and weight—up to 985 lb (446.79 kg) depending on
configuration—we strongly recommend that you install the router by using a router
transport kit or a pallet jack with pallet jack attachment.
12
Copyright © 2015, Juniper Networks, Inc.
Unpack the Router
NOTE: The router is maximally protected inside the shipping crate. Do not
unpack it until you are ready to begin installation.
The shipping container door can be used as a ramp to guide the MX2010 router out of
the crate (see Figure 7 on page 13).
g007441
Figure 7: MX2010 Shipping Crate Door
To unpack the router:
1.
Move the shipping crate to a staging area as close to the installation site as possible,
where you have enough room to remove the components from the chassis. While the
chassis is bolted to the shipping pallet, you can use a forklift or pallet jack to move it.
NOTE: The staging and installation area must be ESD approved.
2. Position the shipping crate with the arrows pointing up.
3. Open all the latches on the shipping crate.
4. Remove the front door of the shipping crate and set it aside.
Copyright © 2015, Juniper Networks, Inc.
13
MX2010 3D Universal Edge Router Quick Start
NOTE: If you ordered a router transport kit, the shipping crate door is used
as a ramp to guide the MX2010 router out of the crate.
5. Using a two-person team, slide the remainder of the shipping crate off the pallet.
6. Remove the foam covering the top of the router.
7. Remove the pallet jack attachment, if ordered.
NOTE: If you ordered a router transport kit, see “Unpack the Router
Transport Kit” on page 24 for instructions on how to unpack and install
the router transport kit.
8. Remove the large mounting tray.
9. Remove the accessory box.
10. Verify the parts received against the lists.
11. Remove the vapor corrosion inhibitor (VCI) packs attached to the pallet, being careful
not to break the VCI packs open.
12. To remove the brackets holding the chassis to the pallet, use a 1/2-in. socket wrench;
and a number 2 Phillips screwdriver to remove the bolts and screws from the brackets.
13. Set the shipping brackets aside for later use to secure the router to the pallet jack
attachment.
NOTE: If you ordered a router transport kit, see “Unpack the Router
Transport Kit” on page 24 for instructions on how to unpack and install
the router transport kit.
14. Save the shipping crate cover and packing materials in case you need to move or ship
the router at a later time.
Remove Components
The router might have field replacement units (FRUs) installed. Remove these FRUs
from the MX2010 router before installing the router into a rack or cabinet, (see
Figure 8 on page 15, Figure 9 on page 16, and Figure 10 on page 17).
14
Copyright © 2015, Juniper Networks, Inc.
Remove Components
Figure 8: Components to Remove from the Front of the MX2010 Router
1
2
OK/FAIL
OK/FAIL
OK/FAIL
OK/FAIL
OK/FAIL
OK/FAIL
OK/FAIL
OK/FAIL
3
4
g007400
5
Remove field replacement units (FRUs) from the front of the MX2010 router before you
install the router. See Table 1 on page 15 for information about MX2010 router
components.
Table 1: Components to Remove from the Front of the MX2010 Router
Component No.
Component
Description
Slots
Number of FRUs
1
Craft interface
–
1
2
Switch Fabric Boards
(SFBs)
0 through 7
8
3
Control Board and
Routing Engine
(CB-RE)
0 and 1
2
4
MPCs with ADCs and
MICs
0 through 9
10
Copyright © 2015, Juniper Networks, Inc.
15
MX2010 3D Universal Edge Router Quick Start
Figure 9: Components to Remove from the Rear of an AC-Powered
MX2010 Router
1
2
3
4
D
5
6
g007447
7
Remove field replacement units (FRUs) from the rear of an AC-powered MX2010 router
before you install the router. See Table 2 on page 16 for information about MX2010 router
components.
Table 2: Components to Remove from the Rear of an AC-Powered MX2010
Router
16
Component
No.
Component
Description
1
Slots
Number of FRUs
Upper fan trays (two)
Fan tray 2 and fan tray 3
(behind cage door)
2
2
AC PDM—Three-phase
delta or wye
PDM1/Input1
1
3
AC PSM
0 through 8
9
4
PSM air filter
–
1
5
AC PDM—Three-Phase
delta or wye
PDM0/Input0
1
6
Fan tray air filter
–
1
7
Lower fan trays (two)
Fan tray 0 and fan tray 1
(behind access door)
2
Copyright © 2015, Juniper Networks, Inc.
Remove Components
Figure 10: Components to Remove from the Rear of a DC-Powered MX2010
Router
1
2
3
4
D
5
6
7
g007401
8
Remove field replacement units (FRUs) from the rear of a DC-powered MX2010 router
before you install the router. See Table 3 on page 17 for information about MX2010 router
components.
Table 3: Components to Remove from the Rear of a DC-Powered MX2010
Router
Component
No.
Component
Description
1
Slots
Number of FRUs
Upper fan trays (two)
Fan tray 2 and fan tray 3
(behind cage door)
2
2
DC PDM
PDM1/Input1
1
3
DC PSM
0 through 8
9
4
PSM air filter
–
1
5
DC PDM
PDM0/Input0
1
6
DC cable manager
–
2
7
Fan tray air filter
–
1
Copyright © 2015, Juniper Networks, Inc.
17
MX2010 3D Universal Edge Router Quick Start
Table 3: Components to Remove from the Rear of a DC-Powered MX2010
Router (continued)
Component
No.
Component
Description
8
Lower fan trays (two)
Slots
Number of FRUs
Fan tray 0 and fan tray 1
(behind access door)
2
To remove the components from the router:
1.
Slide each component out of the chassis evenly so that it does not become stuck or
damaged.
2. Label each component as you remove it so you can reinstall it in the correct location.
NOTE: The MX2010 PSMs can be installed in any order in the chassis.
3. Immediately store each removed component in an electrostatic bag.
4. Do not stack removed components. Lay each one on a flat surface.
To remove the upper and lower fan tray (see Figure 11 on page 19 and
Figure 12 on page 19):
NOTE: The fan trays are interchangeable and are hot-insertable and
hot-removable.
1.
Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect
the strap to an approved site ESD grounding point. See the instructions for your site.
2. Loosen the two captive screws on each side of the fan tray access panel and open.
3. Loosen the two captive screws on the fan tray faceplate.
4. Press and hold the latch while simultaneously pulling the fan tray out approximately
1 to 3 in. Place one hand under the fan tray for support, while pulling the fan tray
completely out of the router.
NOTE: The double latch system is a safety mechanism, so you cannot
pull the fan tray out in one motion.
5. Place each component on an antistatic mat resting on a stable, flat surface.
CAUTION: Do not stack fan trays on one another after you remove them.
18
Copyright © 2015, Juniper Networks, Inc.
Install the Router Using a Pallet Jack with Attachment
g007025
Figure 11: Removing Upper Fan Trays
WARNING: Before removing a fan tray, make sure that the fan blades have
stopped completely.
g007039
Figure 12: Removing Lower Fan Trays
NOTE: For complete instructions on removing router components, see the
MX2010 3D Universal Edge Router Hardware Guide.
Install the Router Using a Pallet Jack with Attachment
•
Install the Pallet Jack Attachment on page 19
•
Use the Pallet Jack with Attachment to Install the Router on page 20
Install the Pallet Jack Attachment
1.
Remove the pallet jack attachment from the shipping crate.
2. Place the pallet jack attachment across both pallet jack legs.
3. Using a 9/16-in. (14 mm) socket wrench, loosen and remove the eight shipping bracket
support torque fasteners that are located on the top of the pallet jack attachment
platform.
Copyright © 2015, Juniper Networks, Inc.
19
MX2010 3D Universal Edge Router Quick Start
4. Using a 9/16-in. (14 mm) socket wrench, loosen the torque fasteners that are located
on the four adjustable pallet jack attachment brackets.
5. Adjust the four pallet jack attachment brackets until they fit under the pallet jack legs.
6. Tighten the torque fasteners using a 9/16-in. (14 mm) socket wrench to secure the
brackets on the pallet jack attachment to the pallet jack (see Figure 13 on page 20).
g000017
Figure 13: Installing MX2010 Pallet Jack Attachment
Use the Pallet Jack with Attachment to Install the Router
Before installing the router, you must remove all components (see “Remove Components”
on page 14). To install the router using a pallet jack with attachment:
1.
Ensure that the rack or cabinet is in its permanent location and is secured to the
building. Ensure that the installation site allows adequate clearance for both airflow
and maintenance. For details, see the MX2010 3D Universal Edge Router Hardware
Guide.
2. Reattach the front and rear shipping covers to the chassis to help move the router.
The handles on the shipping covers are used to guide the chassis during installation.
CAUTION: Do not lift the router by using the handles on the shipping
covers. Use these handles only to help position the router.
20
Copyright © 2015, Juniper Networks, Inc.
Use the Pallet Jack with Attachment to Install the Router
3. Place the pallet jack attachment across both legs and secure the attachment to the
pallet jack.
4. Using a four-person team, load the router onto the pallet jack, making sure it rests
securely on the pallet jack attachment platform (see Figure 14 on page 21).
WARNING: Applying force to any other parts of the chassis other than the
shipping covers can damage the chassis.
g007461
Figure 14: Loading the MX2010 Router onto the Pallet Jack
5. Attach the shipping brackets to the pallet jack attachment by using the existing bracket
screws.
6. On each of the shipping brackets, partially insert screws into the holes to secure the
brackets to the chassis. Tighten all screws. These brackets help prevent the chassis
from tilting.
7. Lower the pallet jack before moving the chassis. Doing this helps distribute the weight
evenly and reduces the risk of tilting or damage to the chassis.
NOTE: An empty MX2010 router weighs approximately 324 lb (146.96 kg).
Copyright © 2015, Juniper Networks, Inc.
21
MX2010 3D Universal Edge Router Quick Start
8. Using the pallet jack, position the router in front of the rack or cabinet, centering it in
front of the rack.
NOTE: If you are installing the MX2010 router into a network cabinet, make
sure that no hardware, device, rack, or cabinet component obstructs the
34-U rack space from access during installation.
9. Using the pallet jack, lift the chassis approximately 0.75 in. (1.9 cm) above the surface
of the mounting shelf (four-post rack) or bottom opening of the rack (open-frame
rack), and position it as close as possible.
NOTE: Because of the short lift capability of the pallet jack, we recommend
that you install the router on the bottom of the rack.
10. Remove the shipping brackets that are attached to the pallet jack attachment and
chassis, and set them aside.
11. Grasp the handles on the shipping covers and carefully slide the router into the rack
(see and Figure 15 on page 23 and Figure 16 on page 24). If you are installing the router
into a four-post rack, continue sliding the router onto the mounting shelf so that the
bottom of the chassis and the mounting shelf overlap by approximately 2 in. (5.0 cm).
12. With four people pushing on the front-mounting flanges, slide the router until the
center-mounting brackets (open-frame racks) or front-mounting flanges (four-post
racks) contact the rack rails. In a four-post rack, the mounting shelf ensures that the
holes in the front-mounting flanges of the chassis align with the holes in the rack rails.
13. Move the pallet jack away from the rack.
14. Insert twelve mounting screws (six on each side) into the mounting holes to secure
the router to the rack.
15. Visually inspect the alignment of the router. If the router is installed properly in the
rack, all the mounting screws on one side of the rack should be aligned with the
mounting screws on the opposite side, and the router should be level.
22
Copyright © 2015, Juniper Networks, Inc.
Use the Pallet Jack with Attachment to Install the Router
g007436
Figure 15: Loading the MX2010 Router into a Four-Post Rack
Copyright © 2015, Juniper Networks, Inc.
23
MX2010 3D Universal Edge Router Quick Start
g007462
Figure 16: Loading the MX2010 Router into an Open-Frame Rack
Install the Router Using a Router Transport Kit
•
Unpack the Router Transport Kit on page 24
•
Install the Router Transport Kit onto the Router on page 26
•
Secure the Router to the Transport Platform on page 28
•
Use the Router Transport Kit to Install the Router in a Four-Post Rack on page 31
•
Use the Router Transport Kit to Install the Router in an Open-Frame Rack on page 38
Unpack the Router Transport Kit
The router transport kit is shipped in a wooden crate. A wooden pallet forms the base of
the crate. Metal clips secure the top and front of the crate in place.
The router transport kit shipping container measures 36 in. (91.4 cm) high, 32 in. (81.3 cm)
wide, and 44.5 in. (113 cm) deep (see Figure 17 on page 25). The total weight of the
container containing the router transport kit is 200 lb (90.71 kg).
24
Copyright © 2015, Juniper Networks, Inc.
Unpack the Router Transport Kit
Figure 17: Router Transport Kit Crate Dimensions
44.5 in
(113 cm)
32 in
(81.3 cm)
Crate door/ramp
36 in.
(91.4 cm)
3 ft
(91.44 cm)
3 ft
(91.44 cm)
3 ft
(91.44 cm)
g000015
3 ft
(91.44 cm)
NOTE: The router transport kit is maximally protected inside the shipping
crate. Do not unpack it until you are ready to begin installation.
To unpack the router transport kit:
1.
Move the router transport kit shipping crate to an ESD-approved staging area, where
you have enough room to remove the kit for assembly.
2. Position the shipping crate with the arrows pointing up.
3. Remove the metal clips on the shipping crate that secure the top and front to the
crate (see Figure 18 on page 25).
g000021
Figure 18: Open Router Transport Kit Shipping Crate
Copyright © 2015, Juniper Networks, Inc.
25
MX2010 3D Universal Edge Router Quick Start
4. Remove the top and front of the shipping crate, and set them aside.
5. Remove the two wing nuts that secure the wooden brace to the shipping crate
platform, and set them aside.
6. Align the crate door with the shipping crate platform, and secure the door to the
platform by using the attached velcro straps (see Figure 19 on page 26).
Figure 19: Router Transport Kit Shipping Crate Door
g000016
Crate door/ramp
7. Remove the router transport kit from the shipping container.
8. Remove the vapor corrosion inhibitor (VCI) packs attached to the pallet, being careful
not to break the VCI packs open.
9. Save the shipping crate cover, pallet, and packing materials in case you need to move
or ship the router transport kit at a later time.
Install the Router Transport Kit onto the Router
NOTE: The router transport kit can be purchased from Juniper Networks.
The router transport kit includes the following components:
26
•
Router transport platform
•
Router transport left and right mounting plates with adjustable wheel assembly
Copyright © 2015, Juniper Networks, Inc.
Install the Router Transport Kit onto the Router
•
Router winch mount with winch strap plate
To install the router transport kit:
1.
Remove the router transport kit from the shipping crate (see “Unpack the Router
Transport Kit” on page 24).
NOTE: The router transport kit weighs approximately 138.5 lb (62.82 kg).
2. Remove the winch strap plate that is secured to the winch mount by using a
9/16-in. (14 mm) socket wrench, and set the plate aside.
3. Using a number 3 Phillips screwdriver, loosen the captive screws that secure the winch
mount to the router transport kit, and set the mount aside.
4. Using a number 3 Phillips screwdriver, loosen the captive screws that secure the router
transport mounting plate and wheel assembly (left and right) to the router transport
platform, and set them aside (see Figure 20 on page 27).
g000019
Figure 20: Preparing the Router Transport Kit for Installation
5. Remove the four shipping brackets that secure the router to the shipping crate platform
by using a 9/16-in. (14 mm) socket wrench and a number 2 Phillips screwdriver, and
set the brackets aside.
6. Align the left router transport mounting plate and wheel assembly (indicated by left
arrow shown on the assembly) with the holes on the left side of the chassis (see
Figure 21 on page 28).
Copyright © 2015, Juniper Networks, Inc.
27
MX2010 3D Universal Edge Router Quick Start
7. Using a number 3 Phillips screwdriver, tighten the captive screws to secure the router
transport mounting plate and wheel assembly to the chassis.
8. Align the right router transport mounting plate and wheel assembly (indicated by right
arrow shown on the assembly) with the holes on the right side of the chassis (see
Figure 21 on page 28).
9. Using a number 3 Phillips screwdriver, tighten the captive screws to secure the router
transport mounting plate and wheel assembly to the chassis.
g000055
Figure 21: Installing the Router Transport Kit onto the MX2010 Router
Secure the Router to the Transport Platform
1.
Ensure that the rack is in its permanent location and is secured to the building. Ensure
that the installation site allows adequate clearance for router transport kit turn ratios,
airflow, and maintenance.
2. Using the shipping crate door as a ramp, secure the door to the crate platform by using
the two metal latches (see Figure 22 on page 29).
28
Copyright © 2015, Juniper Networks, Inc.
Secure the Router to the Transport Platform
g000056
Figure 22: Securing the Crate Door to the Shipping Crate Platform
NOTE: An empty MX2010 weighs approximately 324 lb (146.96 kg).
3. Using a two-person team on either side of the chassis, turn the handles on the router
transport 4–5 times until the chassis is raised approximately 1 in. (2.54 cm), making
sure that the chassis is level.
NOTE: The router transport kit is equipped with four T-shaped levels on
top of each of the four router transport mounting brackets. Make sure the
bubbles within the T-shaped levels are between the lines, indicating the
chassis is level.
CAUTION: Do not raise the chassis above 1 in. (2.54 cm). This will ensure
the router will not tilt when transporting, which can result in injury or
damage to the router.
4. Turn the four wheels on the router transport kit toward the rear of the chassis.
5. Grasping the handles on the shipping covers, carefully guide the chassis down the
crate ramp to the rack location.
Copyright © 2015, Juniper Networks, Inc.
29
MX2010 3D Universal Edge Router Quick Start
WARNING: Do not push or pull the router fast while transporting. Using
excessive speed can cause the wheels to turn abruptly and tilt the router
over.
CAUTION: Do not lift the router by using the handles on the shipping
covers. Use these handles only to help position the router.
6. Position the router transport platform directly under the router, aligning the router
transport platform with the bottom of the chassis by adjusting the four leveling mounts.
NOTE: The router transport platform height can be adjusted from
0.25 in. (0.6 cm) to a maximum of 4 in. (10.16 cm).
7. Secure the router transport platform to the router transport mounting plates by using
the four latch locks (see Figure 23 on page 30).
g000073
Figure 23: Securing the Router Transport Platform
30
Copyright © 2015, Juniper Networks, Inc.
Use the Router Transport Kit to Install the Router in a Four-Post Rack
Use the Router Transport Kit to Install the Router in a Four-Post Rack
Because of the router's size and weight—up to 985 lb (446.79 kg) depending on the
configuration—we recommend that you use a router transport kit to install the router.
NOTE: Four people are needed to install the router into a rack.
CAUTION: Before front-mounting the router in a rack, have a qualified
technician verify that the rack is strong enough to support the router's weight
and is adequately supported at the installation site.
Copyright © 2015, Juniper Networks, Inc.
31
MX2010 3D Universal Edge Router Quick Start
1.
Install the winch strap plate to the rear of the router by tightening the four captive
screws (see Figure 24 on page 32).
g000060
Figure 24: Installing Winch Strap Plate (Four-Post Rack)
2. Using a four-person team, transport the router to the rack installation location and
center it in front of the mounting shelf.
NOTE: A minimum of 38 in. (96.5 cm) of clearance is required to roll the
chassis sideways.
32
Copyright © 2015, Juniper Networks, Inc.
Use the Router Transport Kit to Install the Router in a Four-Post Rack
NOTE: A minimum of 42 in. (106.7 cm) of circular space is required to
rotate the chassis.
NOTE: The router transport kit handles can be removed to accommodate
aisle width.
3. Install the winch mount bracket to the rear rack rails by using the six captive screws,
and tighten the screws (see Figure 25 on page 33).
g000024
Figure 25: Installing Winch Mount Bracket to Rack Rails
4. Adjust the height of the router by turning the handles clockwise until the router
transport platform is aligned with the surface of the mounting shelf and slightly higher
than the mounting shelf (see Figure 26 on page 34).
NOTE: Make sure the bubbles within the T-shaped levels are between
the lines, indicating that the router is level.
Copyright © 2015, Juniper Networks, Inc.
33
MX2010 3D Universal Edge Router Quick Start
5. Adjust the four leveling mounts on the router transport platform until all four leveling
mounts rest firmly on the ground (see Figure 26 on page 34).
g000063
Figure 26: Aligning the MX2010 Router with Rack Mounting Shelf
6. Unlock the four toggle latches that secure the router transport platform to the router
transport mounting plate and wheel assembly.
7. Lift the wheels up by turning the handles counterclockwise so that the weight of the
router is on the router transport platform.
34
Copyright © 2015, Juniper Networks, Inc.
Use the Router Transport Kit to Install the Router in a Four-Post Rack
8. Using a number 3 Phillips screwdriver, loosen the captive screws that secure the router
transport mounting plates and wheel assembly to the chassis, and set them aside
(see Figure 27 on page 35).
g000065
Figure 27: Removing Router Transport Mounting Plate and Wheel
Assembly
9. Attach the winch strap to the winch strap plate at the rear of the router (see
Figure 28 on page 36).
Copyright © 2015, Juniper Networks, Inc.
35
MX2010 3D Universal Edge Router Quick Start
g000067
Figure 28: Attaching Winch Strap to Winch Strap Plate
10. Attach a 1-1/8 in. (28.57 mm) torque-controlled driver or socket wrench to the winch
mechanism and turn clockwise to start pulling the chassis into the rack (see
Figure 29 on page 37).
36
Copyright © 2015, Juniper Networks, Inc.
Use the Router Transport Kit to Install the Router in a Four-Post Rack
g000068
Figure 29: Pulling the MX2010 into the Rack
NOTE: A four-person team is needed to carefully guide the router into the
rack while operating the winch.
Copyright © 2015, Juniper Networks, Inc.
37
MX2010 3D Universal Edge Router Quick Start
NOTE: If the router is not pulled all the way into the rack by the winch
mechanism, grasp the handles on the shipping covers and carefully slide
the router onto the mounting shelf until the front-mounting flanges contact
the rack rails. You must remove the winch bracket to perform this
procedure.
NOTE: There must be a minimum of 45-U of usable rack space when
installing the MX2010 into a 45-U rack.
11. Remove the router transport platform, and set the platform aside.
12. Remove the winch mount and winch strap plate, and set them aside.
13. Insert twelve mounting screws (six on each side) into the mounting holes to secure
the router to the rack.
14. Visually inspect the alignment of the router. To verify that the router is installed properly
in the rack, see that all the mounting screws on one side of the rack are aligned with
the mounting screws on the opposite side and the router is level.
15. Reassemble the router transport kit, and set it aside.
Use the Router Transport Kit to Install the Router in an Open-Frame Rack
NOTE: Four persons are needed to install the router into a rack.
CAUTION: Before front-mounting the router in a rack, have a qualified
technician verify that the rack is strong enough to support the router's weight
and is adequately supported at the installation site.
To install the MX2010 in an open-frame rack by using a router transport kit:
1.
Using the router transport platform, position the router in front of the rack or cabinet,
centering it in front of the rack.
2. Using a four person team, transport the router to the rack installation location and
center it in front of the rack.
NOTE: A minimum of 38 in. (96.5 cm) of clearance is required to roll the
chassis sideways.
NOTE: A minimum of 42 in. (106.7 cm) of circular space is required to
rotate the chassis.
38
Copyright © 2015, Juniper Networks, Inc.
Use the Router Transport Kit to Install the Router in an Open-Frame Rack
NOTE: The router transport kit handles can be removed to accommodate
aisle width.
3. Adjust the height of the router by turning the handles clockwise until the router
transport platform is approximately 0.75 in. (1.9 cm) above the bottom of the rack
opening (see Figure 26 on page 34).
NOTE: Because of the short lift capability of the router transport kit, we
recommend that you install the router on the bottom of the rack.
NOTE: Make sure that the bubbles within the T-shaped levels are between
the lines, indicating that the router is level.
4. Adjust the four leveling mounts on the router transport platform until all four leveling
mounts rest firmly on the ground (see Figure 30 on page 40).
Copyright © 2015, Juniper Networks, Inc.
39
MX2010 3D Universal Edge Router Quick Start
g000064
Figure 30: Aligning the MX2010 Router with the Rack
5. Unlock the four toggle latches that secure the router transport platform to the router
transport mounting plate and wheel assembly.
40
Copyright © 2015, Juniper Networks, Inc.
Use the Router Transport Kit to Install the Router in an Open-Frame Rack
6. Lift the wheels up by turning the handles counterclockwise so that the weight of the
router is on the router transport platform.
7. Using a number 3 Phillips screwdriver, loosen the captive screws that secure the router
transport mounting plates and wheel assembly to the chassis, and set them aside
(see Figure 31 on page 41).
g000066
Figure 31: Removing Router Transport Mounting Plate and Wheel Assembly
8. Grasping the handles on the shipping covers, carefully slide the router into the rack
until the center-mounting brackets contact the rack rails (see Figure 32 on page 42).
Copyright © 2015, Juniper Networks, Inc.
41
MX2010 3D Universal Edge Router Quick Start
g000069
Figure 32: Sliding the MX2010 into the Open-Frame Rack
NOTE: A four-person team is needed to carefully guide the router into the
rack.
NOTE: There must be a minimum of 45-U of usable rack space when you
install the MX2010 into a 45-U rack.
9. Remove the router transport platform, and set the platform aside.
42
Copyright © 2015, Juniper Networks, Inc.
Use the Router Transport Kit to Install the Router in an Open-Frame Rack
10. Secure the router to the rack by using the mounting screws provided by the rack
manufacturer.
11. Visually inspect the alignment of the router. To verify that the router is installed properly
in the rack, see that all the mounting screws on one side of the rack are aligned with
the mounting screws on the opposite side and the router is level.
12. Reassemble the router transport kit, and set it aside.
Copyright © 2015, Juniper Networks, Inc.
43
MX2010 3D Universal Edge Router Quick Start
Step 4: Connect the Grounding Cable
1.
Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect
the strap to an approved site ESD grounding point. See the instructions for your site.
2. Connect the grounding cable to a proper earth ground.
3. Verify that a licensed electrician has attached the cable lug provided with the router
to the grounding cable.
4. Make sure that grounding surfaces are clean and brought to a bright finish before you
make grounding connections.
5. Attach an ESD grounding strap to your bare wrist, and connect the strap to one of the
ESD points on the chassis. For more information about ESD, see the MX2010 3D
Universal Edge Router Hardware Guide.
6. Place the grounding cable lug over the grounding points. The upper pair is sized for
UNC 1/4-20 bolts, and the lower pair is sized for M6 bolts.
7. Secure the grounding cable lug to the grounding points, first with the washers, and
then with the nuts (see Figure 33 on page 44).
g007107
Figure 33: Grounding Points on the MX2010 Router
8. Verify that the grounding cabling is correct, that the grounding cable does not touch
or block access to router components, and that it does not drape where people could
trip on it.
44
Copyright © 2015, Juniper Networks, Inc.
Step 5: Reinstall Components
Step 5: Reinstall Components
To reinstall the components in the router:
1.
Take each component out of its electrostatic bag, and identify the slot on the
component where it will be connected.
NOTE: Remove the shipping covers before installing router components.
2. Slide each component into the chassis evenly so that it does not become stuck or
damaged.
3. Tighten the captive screws, and secure all levers for each component.
NOTE: Make sure that all empty slots are covered with a blank panel before
operating the router.
Copyright © 2015, Juniper Networks, Inc.
45
MX2010 3D Universal Edge Router Quick Start
Step 6: Connect External Devices and Line Card Cables
g007411
Figure 34: Connecting External Devices and MPC Cables
•
Connect to a Network for Out-of-Band Management on page 46
•
Connect a Management Console on page 46
•
Connect the Line Card Cables on page 46
Connect to a Network for Out-of-Band Management
1.
Turn off the power to the management device.
2. Plug one end of an RJ-45 Ethernet cable into the ETHERNET port on the CB-RE.
3. Plug the other end of the cable into the network device.
Connect a Management Console
1.
Turn off the power to the management device.
2. Plug one end of an RJ-45 Ethernet cable into the CONSOLE or AUX port on the CB-RE.
3. Plug the female DB-9 adapter end of the cable into the device's serial port.
Connect the Line Card Cables
1.
Have ready a length of the type of cable used by the MPCs or MICs. For cable
specifications, see the MX Series Interface Module Reference.
2. If the cable connector port is covered by a rubber safety plug, remove the plug.
46
Copyright © 2015, Juniper Networks, Inc.
Connect the Line Card Cables
WARNING: Do not look directly into a fiber-optic transceiver or into the
ends of fiber-optic cable. Fiber-optic transceivers and fiber-optic cable
connected to a transceiver emit laser light that can damage your eyes.
CAUTION: Do not leave a fiber-optic transceiver uncovered except when
inserting or removing cable. The safety cap keeps the port clean and
prevents accidental exposure to laser light.
3. Insert the cable connector into the cable connector port on the faceplate.
4. Arrange the cable in the cable manager system to prevent it from dislodging or
developing stress points. Secure the cable so that it is not supporting its own weight
as it hangs to the floor. Place excess cable out of the way in a neatly coiled loop in
the cable manager system. Placing fasteners on the loop helps to maintain its shape.
CAUTION: Avoid bending fiber-optic cable beyond its minimum bend
radius. An arc smaller than a few inches in diameter can damage the cable
and cause problems that are difficult to diagnose.
CAUTION: Do not let fiber-optic cable hang free from the connector. Do
not allow fastened loops of cable to dangle, which stresses the cable at
the fastening point.
Copyright © 2015, Juniper Networks, Inc.
47
MX2010 3D Universal Edge Router Quick Start
Step 7: Connect Power Cables
Depending on your configuration, your router uses either AC or DC power distribution
modules (PDMs). Perform the appropriate procedures for each PDM in your router. For
more information about PDMs, see the MX2010 3D Universal Edge Router Hardware Guide.
•
Connect Power to a Three-Phase Delta AC Power Distribution Module on page 48
•
Connect Power to a Three-Phase Wye AC Power Distribution Module on page 52
•
Connect AC Power Supply Modules on page 56
•
Connect Power to a DC Power Distribution Module on page 58
•
Connect DC Power Supply Modules on page 60
Connect Power to a Three-Phase Delta AC Power Distribution Module
To connect an AC power cord to an AC power source for the three-phase delta AC PDM:
CAUTION: Do not mix AC and DC power modules within the same router.
1.
Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect
the strap to an approved site ESD grounding point. See the instructions for your site.
2. Switch off the dedicated customer-site circuit breakers. Ensure that the voltage across
the AC power source cable leads is 0 V and that there is no chance that the cable
leads might become active during installation.
3. Detach the ESD grounding strap from the approved site ESD grounding point, and
connect the strap to one of the ESD points on the chassis.
4. Switch off (O) the AC power supply modules (PSMs) and disengage all AC PSMs.
5. Verify that the correct three-phase delta AC PDMs are installed and secured in the
chassis before connecting power cables.
NOTE: The power cables must be uninstalled and removed from the PDM
before removal of the PDM from the chassis.
6. Using a number 2 Phillips (+) screwdriver, unscrew the four captive screws located
on the either side of the metal AC wiring compartment (four screws total per PDM).
7. Remove the cover of the metal AC wiring compartment.
8. Unscrew the retaining nut from the AC power cord.
9. Insert the wires of the AC power cord through the hole of the retaining nut and rubber
grommet.
10. Insert the wires of the AC power cord through the hole of the metal wiring
compartment.
48
Copyright © 2015, Juniper Networks, Inc.
Connect Power to a Three-Phase Delta AC Power Distribution Module
11. Connect the wires to the AC terminal block on the three-phase delta AC PDM (see
Figure 35 on page 49). Loosen the input terminal or grounding point screw, insert each
wire into the grounding point input terminal, and tighten the screw (see
Table 4 on page 50 for approved AC wire gauge).
NOTE: The terminal connections have either slotted screws or hex screws.
Use a 1/4-in. slotted screwdriver for the slotted screws. Use a 5/32-in.
(4-mm) Allen wrench for the 5/16-in. hex screws.
NOTE: The three-phase delta AC PDM must be installed and secured in
the chassis before connecting the power input cables. If the PDM must
be removed, both input power cables must be uninstalled and removed
from the PDM before the PDM can be removed from the chassis. The
MX2010 chassis is not sensitive to phase rotation sequence—either
clockwise or counter clockwise will operate correctly.
To connect wires to the terminal block that serves six PSMs:
a. Insert the grounding wire into the grounding point labeled GND.
b. Insert the wire labeled L1 into the input terminal labeled A1.
c. Insert the wire labeled L2 into the input terminal labeled B1.
d. Insert the wire labeled L3 into the input terminal labeled C1.
g007066
C1
B1
A1
A2
C1
B2
B1
C2
C2
B2
A2
Copyright © 2015, Juniper Networks, Inc.
A1
Figure 35: Connecting Power to a Three-Phase Delta AC Power Distribution
Module
49
MX2010 3D Universal Edge Router Quick Start
NOTE: The three-phase delta AC PDM terminal blocks will be flipped
depending on which slot the PDM gets plugged into.
CAUTION: Wire label configuration is for Juniper Networks supplied cable
only. If you are using your own cable, make sure you use the proper
connections.
To connect wires to the terminal block that serves three PSMs:
a. Insert the grounding wire into the grounding point labeled GND.
b. Insert the wire labeled L1 into the input terminal labeled A2.
c. Insert the wire labeled L2 into the input terminal labeled B2.
d. Insert the wire labeled L3 into the input terminal labeled C2.
WARNING: In order to protect power supplies from input voltage that
might be caused by mis-wired PDMs, before reinstalling the metal cover
to the wiring compartment apply AC voltage to the PDM (with disengaged
PSM) to make sure that two LEDs on the PDM are lit green and that the
AC voltage between AC terminal blocks A1-B1, B1-C1, C1-A1, A2-B2, B2-C2,
and C2-A2 for three-phase delta PDM is not more than 264 VAC when
measured with a digital voltage meter (DVM). Then turn off the AC breaker,
de-energizing the PDM, and install the metal cover and engage all AC
PSMs.
NOTE: The color of each AC power wire might vary.
NOTE: Three-phase delta AC wire assembly kits can be purchased from
Juniper Networks.
Table 4: Supported Three-Phase Delta AC Wire Gauge
Wire Gauge
Description
4 x 6-AWG or equivalent
4 conductor wires, each wire is 6-AWG
NOTE: We recommend that you use the proper gauge wire in order for the
cable clamps to hold the AC cables. Using smaller gauge wiring will result
in the cable clamps not tightening properly.
50
Copyright © 2015, Juniper Networks, Inc.
Connect Power to a Three-Phase Delta AC Power Distribution Module
WARNING: Power connections must be performed by a licensed electrician
only.
12. Verify that the power cable connections are correct.
13. Screw the retaining nut onto the AC power cord to secure it to the metal wiring
compartment.
14. Using a number 2 Phillips (+) screwdriver, tighten the two captive screws on the metal
AC wiring compartment.
15. Use the provided plastic cable tie to fasten the AC power cord to the PDM.
16. Verify that the AC power cord does not touch or block access to router components,
and that it does not drape where people could trip on it.
17. Repeat the procedure for the other three-phase delta AC PDMs.
18. Connect the three-phase delta AC power cord mating connector to the AC power
cord connector (see Figure 36 on page 51). Table 5 on page 51 shows the approved
three-phase delta AC power cord mating connector specifications.
g000037
Figure 36: Three-Phase Delta AC Power Cord Mating Connector
NOTE: The three-phase delta AC power cord mating connector is not
supplied by Juniper Networks.
Table 5: Three-Phase Delta AC Power Cord Mating Cable Connector
Specifications
Cable
Manufacturer Part Number
Description
Three-phase delta
460C9W
60-amp, 250 volt 3-phase,
3-pole, 4-wire, North
American pin and sleeve
connector, industrial grade,
IP67, watertight (blue)
Copyright © 2015, Juniper Networks, Inc.
51
MX2010 3D Universal Edge Router Quick Start
WARNING: Do not touch the power connectors on the PDM. They can contain
dangerous voltages.
Connect Power to a Three-Phase Wye AC Power Distribution Module
CAUTION: Do not mix AC and DC power modules within the same router.
To connect an AC power cord to an AC power source for the three-phase wye AC PDM:
1.
Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect
the strap to an approved site ESD grounding point. See the instructions for your site.
2. Switch off the dedicated customer-site circuit breakers. Ensure that the voltage across
the AC power source cable leads is 0 V and that there is no chance that the cable
leads might become active during installation.
3. Detach the ESD grounding strap from the approved site ESD grounding point, and
connect the strap to one of the ESD points on the chassis.
4. Switch off (O) the AC PSMs and disengage all AC PSMs.
5. Using a number 2 Phillips (+) screwdriver, unscrew the four captive screws located
on the either side of the metal AC wiring compartment (four screws total per PDM).
6. Remove the cover of the metal AC wiring compartment.
7. Unscrew the retaining nut from the AC power cord.
8. Insert the wires of the AC power cord through the hole of the retaining nut and rubber
grommet.
9. Insert the wires of the AC power cord through the hole of the metal wiring
compartment.
10. Connect the wires to the AC terminal block on the three-phase wye AC PDM (see
Figure 37 on page 53). Loosen the input terminal or grounding point screw, insert each
wire into the grounding point or input terminal, and tighten the screw (see
Table 6 on page 54 for approved AC wire gauge).
NOTE: The terminal connections have either slotted screws or hex screws.
Use a 1/4-in. slotted screwdriver for the slotted screws. Use a 5/32-in.
(4-mm) Allen wrench for the 5/16-in. hex screws.
52
Copyright © 2015, Juniper Networks, Inc.
Connect Power to a Three-Phase Wye AC Power Distribution Module
NOTE: The three-phase wye AC PDM must be installed and secured in
the chassis before connecting the power input cables. If the PDM must
be removed, both input power cables must be uninstalled and removed
from the PDM before the PDM can be removed from the chassis. The
MX2010 chassis is not sensitive to phase rotation sequence—either
clockwise or counter clockwise will operate correctly.
To connect wires to the terminal block that serves six PSMs:
a. Insert the grounding wire into the grounding point labeled GND.
b. Insert the wire labeled L1 into the input terminal labeled A1.
c. Insert the wire labeled L2 into the input terminal labeled B1.
d. Insert the wire labeled L3 into the input terminal labeled C1.
e. Insert the wire labeled N into the input terminal labeled N1.
g007082
Figure 37: Connecting Power to a Three-Phase Wye AC Power Distribution
Module
CAUTION: Wire label configuration is for Juniper Networks supplied cable
only. If you are using your own cable, make sure you use the proper
connections.
Copyright © 2015, Juniper Networks, Inc.
53
MX2010 3D Universal Edge Router Quick Start
To connect wires to the terminal block that serves three PSMs:
a. Insert the grounding wire into the grounding point labeled GND.
b. Insert the wire labeled L1 into the input terminal labeled A2.
c. Insert the wire labeled L2 into the input terminal labeled B2.
d. Insert the wire labeled L3 into the input terminal labeled C2.
e. Insert the wire labeled N into the input terminal labeled N2.
WARNING: In order to protect power supplies from input voltage that
might be caused by miswired PDMs, before reinstalling the metal cover
to the wiring compartment apply AC voltage to the PDM (with disengaged
PSM) to make sure that two LEDs on the PDM are lit green and that the
AC voltage between AC terminal blocks A1-N1, B1-N1, C1-N1, A2-N2, B2-N2,
and C2-N2 for three-phase wye PDM is not more than 264VAC when
measured with a DVM. Then turn off the AC breaker, de-energizing the
PDM, and install the metal cover and engage all AC PSMs.
NOTE: The color of each AC power wire might vary.
NOTE: Three-phase wye AC wire assembly kits can be purchased from
Juniper Networks.
Table 6: Supported Three-Phase Wye AC Wire Gauge
Wire Gauge
Description
5 x 10-AWG or equivalent
5 conductor wires, each wire is 10-AWG
NOTE: It is recommended to use the proper gauge wire in order for the
cable clamps to hold the AC cables. Using smaller gauge wiring will result
in the cable clamps not tightening properly.
WARNING: Power connections must be performed by a licensed electrician
only.
11. Verify that the power cable connections are correct.
12. Screw the retaining nut onto the AC power cord to secure it to the metal wiring
compartment.
54
Copyright © 2015, Juniper Networks, Inc.
Connect Power to a Three-Phase Wye AC Power Distribution Module
13. Reinstall the metal PDM wiring cover, and using a number 2 Phillips (+) screwdriver,
tighten the four captive screws on the metal AC wiring compartment.
14. Use the provided plastic cable tie to fasten the AC power cord to the PDM.
15. Verify that the AC power cord does not touch or block access to router components,
and that it does not drape where people could trip on it.
16. Repeat the procedure for the other three-phase wye AC PDMs.
17. Connect the three-phase wye AC power cord mating connector to the AC power cord
connector (see Figure 38 on page 55). Table 7 on page 55 shows the approved
three-phase wye AC power cord mating connector specifications.
g000038
Figure 38: Three-Phase Wye AC Power Cord Mating Connector
Table 7: Three-Phase Wye AC Power Cord Mating Cable Connector
Specifications
Cable
Manufacturer Part Number
Description
Three-phase wye
PCE 225-6
32-amp, 400 volt IP44 3 pole,
5 wire with brass contacts (red)
NOTE: The three-phase wye AC power cord mating connector is not
supplied by Juniper Networks.
WARNING: Do not touch the power connectors on the PDM. They can contain
dangerous voltages.
Copyright © 2015, Juniper Networks, Inc.
55
MX2010 3D Universal Edge Router Quick Start
Connect AC Power Supply Modules
To install an MX2010 AC PSM:
1.
Verify that the power switch on the PSM is in the off (O) position (see
Figure 39 on page 56).
2. Move the input mode DIP switch 0 (left switch) to the ON (top position) for the bottom
feed INP0 (expected to be connected), and DIP switch 1 (right switch) to the ON (top
position) for the top feed INP1 (expected to be connected). If both DIP switches 0
and 1 are turned to the ON position, then both top and bottom feeds are expected to
be connected (see Figure 39 on page 56).
The AC power system provides dual redundant feed. Each PSM takes in two AC feeds
and uses one of the two. Only one of the two feeds is active during power operation.
Each feed is a single-phase AC system 200–240 VAC derived from a three-phase
delta or wye AC input system. In addition, a PSM failure triggers the alarm LED on the
craft interface. Each PDM has an LED per feed indicating whether the feed is active
or not, or whether the feed is connected properly.
Figure 39: Selecting AC Power Subsystem Feed Redundancy
ON
PWR OK FAULT
0 1
INP1
g007109
INP0
3. Ensure that the voltage across the AC power source cable leads is 0 V and that there
is no chance that the cable leads might become active during installation.
4. Using both hands, slide the PSM straight into the chassis until the PSM is fully seated
in the chassis slot. Tighten the two captive screws to secure the PSM to the chassis.
5. Verify that the INP0 or INP1 LEDs on the PSM are lit green steadily. The INP0 or INP1
LEDs are lit yellow if that input’s voltage is in reverse polarity. Check the polarity of
the power cables to fix the condition (see Figure 40 on page 58 and
Table 8 on page 57).
6. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect
the strap to one of the ESD points on the chassis.
7. Move the switch to the on (|) position.
56
Copyright © 2015, Juniper Networks, Inc.
Connect AC Power Supply Modules
8. Verify that the PWR OK LED is lit green steadily. See Table 8 on page 57 for information
about MX2010 AC PSM LEDs.
NOTE: The MX2010 systems configured for three-phase wye AC input
power must use only three-phase wye AC PDMs and AC PSMs. Systems
configured for three-phase delta AC input power must use three-phase
delta AC PDMs and AC PSMs. AC and DC PSMs or PDMs must not be
mixed within a single system.
Table 8: MX2010 AC Power Supply Module LEDs
Label
Color
State
Description
PWR OK
Green
On
Power is functioning normally with no alarms.
Yellow
On
PSM controller is functioning normally.
–
Off
PSM is not functioning normally or the AC input
voltage is out of range.
Red
On
PSM is not functioning normally or the AC input
voltage is out of range.
–
Off
PSM is functioning normally.
Green
On
AC input is within the required voltage range and
the DIP switch is set to on.
Yellow
On
AC input is out of the required voltage range.
–
Off
AC input to the PSM is not present.
Green
On
AC input is within the required voltage range and
the DIP switch is set to on.
Yellow
On
AC input is out of the required voltage range.
–
Off
AC input to the PSM is not present.
FAULT
INP0
INP1
9. Repeat Steps 1 through 8 for installing PSMs in slots 0, 1, and 2, where required.
Copyright © 2015, Juniper Networks, Inc.
57
MX2010 3D Universal Edge Router Quick Start
g007060
Figure 40: MX2010 AC Power Supply Module Front View
NOTE: Each PSM slot not occupied by an AC PSM must be covered by a
PSM blank panel.
Connect Power to a DC Power Distribution Module
1.
Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect
the strap to one of the ESD points on the chassis. For more information about ESD,
see the MX2010 3D Universal Edge Router Hardware Guide.
NOTE: If the DC PSMs are installed in the router, make sure the power
switch is turned to the off (O) position.
2. Ensure that the voltage across the DC power source cable leads is 0 V and that there
is no chance that the cable leads might become active during installation.
3. Remove the DC PDM from the electrostatic bag.
4. Using both hands, slide the PDM part way into the chassis.
5. Open the two locking levers on either side of the PDM, and align them with the openings
in the chassis.
6. Using both hands, push firmly on both spring-loaded levers until the PDM is fully seated
in the chassis slot. The PDM faceplate should be flush. Tighten both captive screws.
NOTE: Make sure that the DC circuit feed switch on the PDM faceplate
matches the current rating amperage—60 Aor 80 A. This switch applies
to all inputs of this PDM, and selecting 60 A reduces the available power
output capacity of the PSMs supplied by this PDM.
58
Copyright © 2015, Juniper Networks, Inc.
Connect Power to a DC Power Distribution Module
7. Loosen the captive screws on the clear plastic cable restraint protecting the terminal
studs on the faceplate of the PDM.
8. Secure each power cable lug to the terminal studs, first with the flat washer, then
with the split washer, and finally with the nut. Apply between 23 lb-in. (2.6 Nm) and
25 lb-in. (2.8 Nm) torque to each nut (see Figure 41 on page 59). Do not overtighten
the nut. (Use a 7/16-in. [11 mm] torque-controlled driver or socket wrench.)
Table 9 on page 59 describes the DC operating range specifications.
a. Attach the positive (+) DC source power cable lug to the RTN (return) terminal.
b. Attach the negative (–) DC source power cable lug to the –48V (input) terminal.
Table 9: MX2010 DC Power System Input Voltage
Item
Specification
DC input voltage
Operating range: –40 through –72 VDC
Figure 41: Connecting Ground and DC Power Cables
Cable
Flat
washer lug
Split
washer
Terminal
studs
Nut
Grounding points
(on chassis)
g007053
D
CAUTION: Ensure that each power cable lug seats flush against the surface
of the terminal block as you are tightening the nuts. Ensure that each nut
is properly threaded onto the terminal stud. The nut should be able to spin
freely with your fingers when it is first placed onto the terminal stud.
Applying installation torque to the nut when the nut is improperly threaded
might result in damage to the terminal stud.
Copyright © 2015, Juniper Networks, Inc.
59
MX2010 3D Universal Edge Router Quick Start
CAUTION: The maximum torque rating of the terminal studs on the DC
PDM is 25 lb-in. (33.89 Nm). The terminal studs might be damaged if
excessive torque is applied. Use only a torque-controlled driver or socket
wrench to tighten nuts on the DC PDM terminal studs.
NOTE: For information about connecting to DC power sources, see the
MX2010 3D Universal Edge Router Hardware Guide.
9. Connect each DC power cable to the appropriate external DC power source.
NOTE: For information about connecting to external DC power sources,
see the MX2010 3D Universal Edge Router Hardware Guide.
10. Switch on the external circuit breakers to provide voltage to the DC power source
cable leads.
NOTE: Each PDM must be connected to a dedicated 60 Aor 80 A DC circuit
breaker for the DC power source. The PDM has a switch to accommodate
DC circuit breaker amperage.
11. Verify that the power cabling is correct, that the cables are not touching, and that they
do not block access to router components or drape where people could trip on them.
12. Close the cable restraint cover over the terminal studs, and tighten the captive screws.
Connect DC Power Supply Modules
To install an MX2010 DC PSM:
1.
Verify that the power switch on the PSM is in the off (O) position (see
Figure 42 on page 61).
2. Move the input mode DIP switch 0 (left switch) to the ON (top position) for the bottom
feed INP0 (expected to be connected), and DIP switch 1 (right switch) to the ON (top
position) for the top feed INP1 (expected to be connected). If both DIP switches 0
and 1 are turned to the ON position, then both top and bottom feeds are expected to
be connected, (see Figure 42 on page 61).
The DC power subsystem is feed redundant. Each DC PSM can be connected to two
separate feeds from different sources that are used to provide feed redundancy. If
two feeds are connected, PSM input power is drawn from the feed with the higher
voltage present. There are two PDMs per power subsystem capable of carrying nine
feeds each. Connect feeds from one source to one PDM and feeds from the other
source to the second PDM of the power subsystem. The primary input of the PSM is
a dual redundant feed, labeled INP0 and INP1. Both feeds are active during operation,
60
Copyright © 2015, Juniper Networks, Inc.
Connect DC Power Supply Modules
but both feeds might or might not be providing current. In addition, a PSM failure
triggers the alarm LED on the craft interface. Each PDM has an LED per feed indicating
whether the feed is active or not, or whether the feed is connected properly.
Figure 42: Selecting DC Power Subsystem Feed Redundancy
ON
PWR OK FAULT
0 1
INP1
g007109
INP0
3. Ensure that the voltage across the DC power source cable leads is 0 V and that there
is no chance that the cable leads might become active during installation.
4. Using both hands, slide the PSM straight into the chassis until the PSM is fully seated
in the chassis slot. Tighten the two captive screws to secure the PSM to the chassis.
NOTE: The MX2010 systems configured for DC input power must use only
DC PDMs and DC PSMs. AC and DC PSMs or PDMs must not be mixed
within a single system.
5. Verify that the INP0 or INP1 LEDs on the PSM is lit green steadily. The INP0 or INP1
LED is lit yellow if that input’s voltage is in reverse polarity. Check the polarity of the
power cables to fix the condition (see Figure 43 on page 62 and Table 10 on page 62).
6. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect
the strap to one of the ESD points on the chassis.
7. Move the switch to the on (|) position.
8. Verify that the PWR OK LED is lit green steadily. See Table 10 on page 62 for information
about MX2010 DC PSM LEDs.
Copyright © 2015, Juniper Networks, Inc.
61
MX2010 3D Universal Edge Router Quick Start
Table 10: MX2010 DC Power Supply Module LEDs
Label
Color
State
Description
PWR OK
Green
On
PSM is functioning normally with no alarms.
Yellow
On
PSM controller is functioning normally.
–
Off
PSM is not functioning normally or the PSM controller
is off.
Red
On
PSM is not functioning normally or the DC input
voltage of one or more feeds is out of range.
–
Off
PSM is functioning normally or both DIP switches
are set to off.
Green
On
DC input is within required voltage range and the DIP
switch is set to on.
Yellow
On
DC input is detected but voltage is out of range.
–
Off
DC input to the PSM is not present.
Green
On
DC input is within required voltage range and the DIP
switch is set to on.
Yellow
On
DC input is detected but voltage is out of range.
–
Off
DC input to the PSM is not present.
FAULT
INP0
INP1
9. Repeat Steps 1 through 8 for installing PSMs in slots 0, 1, and 2, where required.
g007047
Figure 43: MX2010 DC Power Supply Module Front View
62
Copyright © 2015, Juniper Networks, Inc.
Connect DC Power Supply Modules
NOTE: Each PSM slot not occupied by a DC PSM must be covered by a
PSM blank panel.
Copyright © 2015, Juniper Networks, Inc.
63
MX2010 3D Universal Edge Router Quick Start
Step 8: Perform Initial Software Configuration
This procedure connects the router to the network but does not enable it to forward
traffic. For complete information about configuring the router to forward traffic, including
examples, see the Junos OS configuration guides.
Check the LEDs on the craft interface to verify the hardware status after reinstalling or
powering on the MX2010 router.
For a list of system status verification commands, see the MX2010 3D Universal Edge
Router Hardware Guide at http://www.juniper.net/techpubs/.
To configure the software:
•
Enter Configuration Mode on page 64
•
Configure User Accounts and Passwords on page 64
•
Configure System Attributes on page 65
•
Commit the Configuration on page 66
Enter Configuration Mode
1.
Verify that the network device is powered on.
2. Log in as the root user. There is no password.
Amnesiac <ttyd0>
login: root
3. Start the CLI.
root@% cli
root>
4. Enter configuration mode.
root> configure
Entering configuration mode.
[edit]
root#
Configure User Accounts and Passwords
For information about using an encrypted password or an SSH public key string (DSA or
RSA), see authentication.
1.
Add a password to the root administration user account. Enter a clear-text password.
[edit]
root# set system root-authentication plain-text-password
New password: password
Retype new password: password
2. Create a management console user account.
[edit]
64
Copyright © 2015, Juniper Networks, Inc.
Configure System Attributes
root# set system login user user-name authentication plain-text-password
New Password: password
Retype new password: password
3. Set the user account class to super-user.
[edit]
root@# set system login user user-name class super-user
Configure System Attributes
For more information about configuring the backup routing and static routes, see the
Junos OS Administration Library for Routing Devices.
1.
Configure the name of the router. If the name includes spaces, enclose the name in
quotation marks (“ ”).
[edit]
root# set system host-name host-name
NOTE: The DNS server does not use the hostname to resolve to the correct
IP address. This hostname is used to display the name of the Routing
Engine in the CLI. For example, the configured value for the following
user-nameand host-name appears on the command-line prompt when
the user is logged in to the CLI:
[email protected]>
2. Configure the IP address of the DNS server.
[edit]
root# set system name-server address
3. Configure the router’s domain name.
[edit]
roott# set system domain-name domain-name
4. Configure the IP address and prefix length for the router’s management Ethernet
interface.
[edit]
root # set interfaces fxp0 unit 0 family inet address address/prefix-length
5. Configure the IP address of a backup Routing Engine. The backup Routing Engine is
used while the local router is booting and if the routing process fails to start. After the
routing process starts, the backup Routing Engine address is removed from the local
routing and forwarding tables.
[edit]
root# set system backup-router address
6. (Optional) Configure the static routes to remote subnets with access to the
management Ethernet port. Access to the management Ethernet port is limited to
the local subnet. To access the management Ethernet port from a remote subnet,
you must add a static route to that subnet within the routing table.
Copyright © 2015, Juniper Networks, Inc.
65
MX2010 3D Universal Edge Router Quick Start
[edit]
root# set routing-options static route remote-subnet next-hop destination-IP retain
no-readvertise
7. Configure the telnet service at the [edit system services] hierarchy level.
[edit]
root#set system services telnet
Commit the Configuration
1.
Display the configuration to verify that it is correct.
[edit]
root@# show
system {
host-name host-name;
domain-name domain-name;
backup-router address;
root-authentication {
authentication-method (password | public-key);
}
name-server {
address;
}
}
interfaces {
fxp0 {
unit 0 {
family inet {
address address/prefix-length;
}
}
}
}
2. Commit the configuration to activate it on the router.
[edit]
root@# commit
3. Optionally, configure additional properties by adding the necessary configuration
statements. Then commit the changes to activate them on the router.
[edit]
[email protected]# commit
4. When you have finished configuring the router, exit configuration mode.
[edit]
[email protected]# exit
[email protected]>
66
Copyright © 2015, Juniper Networks, Inc.
Safety Warnings
Safety Warnings
WARNING: See installation instructions before connecting the router. This
is a summary of safety warnings. For a complete list of warnings for this
router, including translations, see the MX2010 3D Universal Edge Router
Hardware Guide. Other services should be performed by aut at
http://www.juniper.net/techpubs/.
WARNING: The intrabuilding port(s) of the router is suitable for connection
to intrabuilding or unexposed wiring or cabling only. The intrabuilding port(s)
of the router MUST NOT be metallically connected to interfaces that connect
to the OSP or its wiring. These interfaces are designed for use as intrabuilding
interfaces only (Type 2 or Type 4 ports as described in GR-1089-CORE, Issue
4) and require isolation from the exposed OSP cabling. The addition of primary
protectors is not sufficient protection to connect these interfaces metallically
to OSP wiring.
CAUTION: Before removing or installing components of a router, attach an
ESD strap to an ESD point and place the other end of the strap around your
bare wrist. Failure to use an ESD strap could result in damage to the router.
CAUTION: Use an external surge protective device (SPD) at the AC input of
the router.
•
Only trained and qualified personnel should install or replace the router.
•
Perform only the procedures described in this Quick Start or in the MX2010 3D Universal
Edge Router Hardware Guide. Other services should be performed by authorized service
personnel only.
•
Read the installation instructions before you connect the router to a power source.
•
Before installing the router, read the guidelines for site preparation in the MX2010 3D
Universal Edge Router Hardware Guide to make sure that the site meets power,
environmental, and clearance requirements for the router.
•
For the cooling system to function properly, the airflow around the chassis must be
unrestricted. Allow at least 36 in. (91.44 cm) of clearance between front to rear-cooled
routers. Allow 2.8 in. (7 cm) between the side of the chassis and any non-heat-producing
surface such as a wall.
•
Four people are required to move the MX2010 router.
•
Always remove the front and rear shipping covers before removing the components.
Copyright © 2015, Juniper Networks, Inc.
67
MX2010 3D Universal Edge Router Quick Start
•
Always remove all components before moving the router. The empty router weighs
324 lb (146.96 kg).
•
When installing the router, do not use a ramp inclined more than 10 degrees.
•
Measure the shipping container to make sure there is adequate clearance through
doorways and passages to accommodate the dimensions.
NOTE: The shipping container (wooden crate) is 66.25 in. (168.27 cm)
high, 48 in. (121.92 cm) deep, and 42 in. (106.68 cm) wide.
•
Always reinstall the front and rear shipping covers to help move the router.
WARNING: The shipping covers help prevent damage to the card cage and
backplanes during rack installation.
68
•
When installing components into the router, load the chassis from the bottom to the
top.
•
After installing components, install the EMI cover over the line cards.
•
If the rack is provided with stabilizing devices, install the stabilizers before mounting
or servicing the router in the rack.
•
When removing or installing an electrical component, always place it component-side
up on a flat antistatic surface or in an electrostatic bag.
•
When you install the router, always make the ground connection first and disconnect
it last.
•
Wire the DC PDMs by using the appropriate lugs. When you connect power, the proper
wiring sequence is ground to ground, +RTN to +RTN, then –48 V to –48 V. When you
disconnect power, the proper wiring sequence is –48 V to –48 V, +RTN to +RTN, then
ground to ground. Always connect the ground wire first and disconnect it last.
•
Do not work on the system or connect or disconnect cables during electrical storms.
•
Before working on equipment that is connected to power lines, remove jewelry, including
rings, necklaces, and watches. Metal objects heat up when connected to power and
ground and can cause serious burns or become welded to the terminals.
•
Failure to observe these safety warnings can result in serious physical injury.
•
AC power cable warning (Japan):
Copyright © 2015, Juniper Networks, Inc.
Compliance Statements for NEBS
WARNING: The attached power cable is only for this product. Do not use
the cable for another product.
Compliance Statements for NEBS
•
The equipment is suitable for installation as part of the Common Bonding Network
(CBN).
•
The equipment is suitable for installation in locations where the National Electrical
Code (NEC) applies.
•
The battery return connection is to be treated as an isolated DC return (i.e. DC-I), as
defined in GR-1089-CORE.
•
For Juniper systems with AC power supplies, an external surge protective device (SPD)
must be used at the AC power source.
Compliance Statements for EMC Requirements
•
Canada on page 69
•
European Community on page 69
•
Israel on page 70
•
Japan on page 70
•
United States on page 70
Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
European Community
This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Copyright © 2015, Juniper Networks, Inc.
69
MX2010 3D Universal Edge Router Quick Start
Israel
Translation from Hebrew—Warning: This product is Class A. In residential environments,
the product may cause radio interference, and in such a situation, the user may be required
to take adequate measures.
Japan
Translation from Japanese—This is a Class A product. In a domestic environment this
product may cause radio interference in which case the user may be required to take
adequate measures. VCCI-A
United States
The hardware equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
70
Copyright © 2015, Juniper Networks, Inc.
Junos OS Documentation and Release Notes
Junos OS Documentation and Release Notes
For a list of related Junos OS documentation, see
http://www.juniper.net/techpubs/software/junos/.
If the information in the latest release notes differs from the information in the
documentation, follow the Junos OS Release Notes.
®
To obtain the most current version of all Juniper Networks technical documentation,
see the product documentation page on the Juniper Networks website at
http://www.juniper.net/techpubs/.
Requesting Technical Support
Technical product support is available through the Juniper Networks Technical Assistance
Center (JTAC). If you are a customer with an active J-Care or JNASC support contract,
or are covered under warranty, and need postsales technical support, you can access
our tools and resources online or open a case with JTAC.
•
JTAC policies—For a complete understanding of our JTAC procedures and policies,
review the JTAC User Guide located at
http://www.juniper.net/us/en/local/pdf/resource-guides/7100059-en.pdf.
•
Product warranties—For product warranty information, visit
http://www.juniper.net/support/warranty/.
•
JTAC Hours of Operation —The JTAC centers have resources available 24 hours a day,
7 days a week, 365 days a year.
Self-Help Online Tools and Resources
For quick and easy problem resolution, Juniper Networks has designed an online
self-service portal called the Customer Support Center (CSC) that provides you with the
following features:
•
Find CSC offerings: http://www.juniper.net/customers/support/
•
Find product documentation: http://www.juniper.net/techpubs/
•
Find solutions and answer questions using our Knowledge Base: http://kb.juniper.net/
•
Download the latest versions of software and review release notes:
http://www.juniper.net/customers/csc/software/
•
Search technical bulletins for relevant hardware and software notifications:
http://kb.juniper.net/InfoCenter/
•
Join and participate in the Juniper Networks Community Forum:
http://www.juniper.net/company/communities/
•
Open a case online in the CSC Case Management tool: http://www.juniper.net/cm/
Copyright © 2015, Juniper Networks, Inc.
71
MX2010 3D Universal Edge Router Quick Start
To verify service entitlement by product serial number, use our Serial Number Entitlement
(SNE) Tool: https://tools.juniper.net/SerialNumberEntitlementSearch/
Opening a Case with JTAC
You can open a case with JTAC on the Web or by telephone.
•
Use the Case Management tool in the CSC at http://www.juniper.net/cm/.
•
Call 1-888-314-JTAC (1-888-314-5822 toll-free in the USA, Canada, and Mexico).
For international or direct-dial options in countries without toll-free numbers, visit us at
http://www.juniper.net/support/requesting-support.html
Revision History
January 2015—530-055063. Revision 1. Minor updates.
July 2014—Minor updates.
April 2014—Added information on PDM slot numbering and DIP switches.
January 2014—Added procedures for installing the MX2010 router using the router
transport kit.
May 2013—530-051881. Revision 1. Initial release.
Copyright © 2015, Juniper Networks, Inc. All rights reserved.
Juniper Networks, Junos, Steel-Belted Radius, NetScreen, and ScreenOS are registered trademarks of Juniper Networks, Inc. in the United
States and other countries. The Juniper Networks Logo, the Junos logo, and JunosE are trademarks of Juniper Networks, Inc. All other
trademarks, service marks, registered trademarks, or registered service marks are the property of their respective owners.
Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper Networks reserves the right to change, modify,
transfer, or otherwise revise this publication without notice.
72
Copyright © 2015, Juniper Networks, Inc.